Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/gi…

…t/arm/arm-soc

Pull ARM SoC device tree updates from Arnd Bergmann:
 "We get a moderate number of new machines this time, and only one new
  SoC variant (Actions S700):

  Actions:
   - S700 Soc and CubieBoard7 development board
   - Allo.com Sparky Single-board-computer

  Allwinner:
   - Orange Pi R1 development board
   - Libre Computer Board ALL-H3-CC H3 single-board computer

  ASpeed ast2x00:
   - Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
   - Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
   - Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400

  AT91:
   - Axentia Nattis/Natte digital signage
   - sama5d2 PTC-ek Evaluation board

  Freescale/NXP i.MX:
   - SolidRun Humminboard2 development board
   - Variscite DART-MX6 SoM and Carrier-board
   - Technologic TS-4600 and TS-7970 development board
   - Toradex Colibri iMX7D SoM board
   - v1.5 variant of Solidrun Cubox-i and Hummingboard

  Freescale/NXP Layerscape:
   - Moxa UC-8410A Series industrial computer

  Gemini:
   - D-Link DNS-313 NAS enclosure

  OMAP:
   - LogicPD OMAP35xx SOM-LV devkit
   - LogicPD OMAP35xx Torpedo devkit

  Renesas:
   - r8a77970 (V3M) Starter Kit board
   - r8a7795 (M3-W) Salvator-XS board

  We finally managed to get the dtc warnings under control, with no more
  build-time warnings for bad device tree files. This includes fixes for
  the majority of platforms, including nomadik, samsung, lpc32xx, STi,
  spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
  renesas, hisilicon, and broadcom.

  Files get rearranged on a few platforms, in particular the Marvell
  Armada 7K/8K device tree files are changed in preparation for future
  SoC support, based on more than two of the same chips in one package,
  and some boards get renamed for oxnas for consistency.

  Finally, many existing SoCs gain descriptions for additional on-chip
  devices that we can now support with kernel drivers:

   - Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
   - Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
   - Aspeed clk controller support
   - Freescale LS1088A, LS1021A device support
   - Gemini Ethernet, PCI, TVE, panel
   - Keystone gpio, qspi, more uarts
   - Mediatek cpufreq, regulator, clock, reset
   - Marvell thermal, cpufreq, nand
   - Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
   - Rockchip Mipi, GPU, display
   - Samsung Exynos5433 PMU, power domain, nfc
   - Spreadtrum: sc9860 clocks
   - Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
  arm64: dts: stratix10: fix SPI settings
  ARM: dts: socfpga: add i2c reset signals
  arm64: dts: stratix10: add USB ECC reset bit
  arm64: dts: stratix10: enable USB on the devkit
  ARM: dts: socfpga: disable over-current for Arria10 USB devkit
  ARM: dts: Nokia N9: add support for up/down keys in the dts
  ARM: dts: nomadik: add interrupt-parent for clcd
  ARM: dts: Add ethernet to a bunch of platforms
  ARM: dts: Add ethernet to the Gemini SoC
  ARM: dts: rename oxnas dts files
  ARM: dts: s5pv210: add interrupt-parent for ohci
  ARM: lpc3250: fix uda1380 gpio numbers
  ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
  ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
  ARM: dts: n900: Add aliases for lcd and tvout displays
  ARM: dts: Update ti-sysc data for existing users
  ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
  arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
  arm: spear13xx: Fix spics gpio controller's warning
  arm: spear13xx: Fix dmas cells
  ...

Documentation/devicetree/bindings/arm/actions.txt

@@ -21,10 +21,26 @@ Boards:
 
 Root node property compatible must contain, depending on board:
 
+ - Allo.com Sparky: "allo,sparky"
  - Cubietech CubieBoard6: "cubietech,cubieboard6"
  - LeMaker Guitar Base Board rev. B: "lemaker,guitar-bb-rev-b", "lemaker,guitar"
 
 
+S700 SoC
+========
+
+Required root node properties:
+
+- compatible :  must contain "actions,s700"
+
+
+Boards:
+
+Root node property compatible must contain, depending on board:
+
+ - Cubietech CubieBoard7: "cubietech,cubieboard7"
+
+
 S900 SoC
 ========
 

Documentation/devicetree/bindings/arm/atmel-at91.txt

@@ -90,38 +90,6 @@ System Timer (ST) required properties:
 Its subnodes can be:
 - watchdog: compatible should be "atmel,at91rm9200-wdt"
 
-TC/TCLIB Timer required properties:
-- compatible: Should be "atmel,<chip>-tcb".
-  <chip> can be "at91rm9200" or "at91sam9x5"
-- reg: Should contain registers location and length
-- interrupts: Should contain all interrupts for the TC block
-  Note that you can specify several interrupt cells if the TC
-  block has one interrupt per channel.
-- clock-names: tuple listing input clock names.
-	Required elements: "t0_clk", "slow_clk"
-	Optional elements: "t1_clk", "t2_clk"
-- clocks: phandles to input clocks.
-
-Examples:
-
-One interrupt per TC block:
-	tcb0: timer@fff7c000 {
-		compatible = "atmel,at91rm9200-tcb";
-		reg = <0xfff7c000 0x100>;
-		interrupts = <18 4>;
-		clocks = <&tcb0_clk>;
-		clock-names = "t0_clk";
-	};
-
-One interrupt per TC channel in a TC block:
-	tcb1: timer@fffdc000 {
-		compatible = "atmel,at91rm9200-tcb";
-		reg = <0xfffdc000 0x100>;
-		interrupts = <26 4 27 4 28 4>;
-		clocks = <&tcb1_clk>;
-		clock-names = "t0_clk";
-	};
-
 RSTC Reset Controller required properties:
 - compatible: Should be "atmel,<chip>-rstc".
   <chip> can be "at91sam9260" or "at91sam9g45" or "sama5d3"

Documentation/devicetree/bindings/arm/axentia.txt

@@ -10,6 +10,15 @@ compatible = "axentia,linea",
 and following the rules from atmel-at91.txt for a sama5d31 SoC.
 
 
+Nattis v2 board with Natte v2 power board
+-----------------------------------------
+
+Required root node properties:
+compatible = "axentia,nattis-2", "axentia,natte-2", "axentia,linea",
+	     "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+and following the rules from above for the axentia,linea CPU module.
+
+
 TSE-850 v3 board
 ----------------
 

Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt

@@ -20,4 +20,5 @@ ethsys: clock-controller@1b000000 {
 	compatible = "mediatek,mt2701-ethsys", "syscon";
 	reg = <0 0x1b000000 0 0x1000>;
 	#clock-cells = <1>;
+	#reset-cells = <1>;
 };

Documentation/devicetree/bindings/arm/shmobile.txt

@@ -104,12 +104,16 @@ Boards:
     compatible = "renesas,salvator-x", "renesas,r8a7796"
   - Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S)
     compatible = "renesas,salvator-xs", "renesas,r8a7795"
+  - Salvator-XS (Salvator-X 2nd version, RTP0RC7796SIPB0012S)
+    compatible = "renesas,salvator-xs", "renesas,r8a7796"
   - SILK (RTP0RC7794LCB00011S)
     compatible = "renesas,silk", "renesas,r8a7794"
   - SK-RZG1E (YR8A77450S000BE)
     compatible = "renesas,sk-rzg1e", "renesas,r8a7745"
   - SK-RZG1M (YR8A77430S000BE)
     compatible = "renesas,sk-rzg1m", "renesas,r8a7743"
+  - V3MSK
+    compatible = "renesas,v3msk", "renesas,r8a77970"
   - Wheat
     compatible = "renesas,wheat", "renesas,r8a7792"
 

Documentation/devicetree/bindings/arm/technologic.txt

@@ -1,6 +1,11 @@
 Technologic Systems Platforms Device Tree Bindings
 --------------------------------------------------
 
+TS-4600 is a System-on-Module based on the Freescale i.MX28 System-on-Chip.
+It can be mounted on a carrier board providing additional peripheral connectors.
+Required root node properties:
+	- compatible = "technologic,imx28-ts4600", "fsl,imx28"
+
 TS-4800 board
 Required root node properties:
 	- compatible = "technologic,imx51-ts4800", "fsl,imx51";
@@ -10,3 +15,9 @@ It can be mounted on a carrier board providing additional peripheral connectors.
 Required root node properties:
 	- compatible = "technologic,imx6dl-ts4900", "fsl,imx6dl"
 	- compatible = "technologic,imx6q-ts4900", "fsl,imx6q"
+
+TS-7970 is a System-on-Module based on the Freescale i.MX6 System-on-Chip.
+It can be mounted on a carrier board providing additional peripheral connectors.
+Required root node properties:
+	- compatible = "technologic,imx6dl-ts7970", "fsl,imx6dl"
+	- compatible = "technologic,imx6q-ts7970", "fsl,imx6q"

Documentation/devicetree/bindings/bus/ti-sysc.txt

@@ -26,6 +26,8 @@ Required standard properties:
 		or one of the following derivative types for hardware
 		needing special workarounds:
 
+		"ti,sysc-omap2-timer"
+		"ti,sysc-omap4-timer"
 		"ti,sysc-omap3430-sr"
 		"ti,sysc-omap3630-sr"
 		"ti,sysc-omap4-sr"
@@ -49,6 +51,26 @@ Required standard properties:
 
 Optional properties:
 
+- ti,sysc-mask	shall contain mask of supported register bits for the
+		SYSCONFIG register as documented in the Technical Reference
+		Manual (TRM) for the interconnect target module
+
+- ti,sysc-midle	list of master idle modes supported by the interconnect
+		target module as documented in the TRM for SYSCONFIG
+		register MIDLEMODE bits
+
+- ti,sysc-sidle	list of slave idle modes supported by the interconnect
+		target module as documented in the TRM for SYSCONFIG
+		register SIDLEMODE bits
+
+- ti,sysc-delay-us	delay needed after OCP softreset before accssing
+			SYSCONFIG register again
+
+- ti,syss-mask	optional mask of reset done status bits as described in the
+		TRM for SYSSTATUS registers, typically 1 with some devices
+		having separate reset done bits for children like OHCI and
+		EHCI
+
 - clocks	clock specifier for each name in the clock-names as
 		specified in the binding documentation for ti-clkctrl,
 		typically available for all interconnect targets on TI SoCs
@@ -61,6 +83,9 @@ Optional properties:
 - ti,hwmods	optional TI interconnect module name to use legacy
 		hwmod platform data
 
+- ti,no-reset-on-init	interconnect target module should not be reset at init
+
+- ti,no-idle-on-init	interconnect target module should not be idled at init
 
 Example: Single instance of MUSB controller on omap4 using interconnect ranges
 using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000):
@@ -74,6 +99,17 @@ using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000):
 		reg-names = "rev", "sysc", "syss";
 		clocks = <&l3_init_clkctrl OMAP4_USB_OTG_HS_CLKCTRL 0>;
 		clock-names = "fck";
+		ti,sysc-mask = <(SYSC_OMAP2_ENAWAKEUP |
+				 SYSC_OMAP2_SOFTRESET |
+				 SYSC_OMAP2_AUTOIDLE)>;
+		ti,sysc-midle = <SYSC_IDLE_FORCE>,
+				<SYSC_IDLE_NO>,
+				<SYSC_IDLE_SMART>;
+		ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+				<SYSC_IDLE_NO>,
+				<SYSC_IDLE_SMART>,
+				<SYSC_IDLE_SMART_WKUP>;
+		ti,syss-mask = <1>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x2b000 0x1000>;

Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt

@@ -5,8 +5,11 @@ controllers within the SoC.
 
 Required Properties:
 
-- compatible: should be "amlogic,gxbb-clkc" for GXBB SoC,
-	      or "amlogic,gxl-clkc" for GXL and GXM SoC.
+- compatible: should be:
+		"amlogic,gxbb-clkc" for GXBB SoC,
+		"amlogic,gxl-clkc" for GXL and GXM SoC,
+		"amlogic,axg-clkc" for AXG SoC.
+
 - reg: physical base address of the clock controller and length of memory
        mapped region.
 

Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt

@@ -0,0 +1,41 @@
+Solomon Goldentek Display GKTW70SDAE4SE LVDS Display Panel
+==========================================================
+
+The GKTW70SDAE4SE is a 7" WVGA TFT-LCD display panel.
+
+These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt
+with the following device-specific properties.
+
+Required properties:
+
+- compatible: Shall contain "sgd,gktw70sdae4se" and "panel-lvds", in that order.
+
+Example
+-------
+
+panel {
+	compatible = "sgd,gktw70sdae4se", "panel-lvds";
+
+	width-mm = <153>;
+	height-mm = <86>;
+
+	data-mapping = "jeida-18";
+
+	panel-timing {
+		clock-frequency = <32000000>;
+		hactive = <800>;
+		vactive = <480>;
+		hback-porch = <39>;
+		hfront-porch = <39>;
+		vback-porch = <29>;
+		vfront-porch = <13>;
+		hsync-len = <47>;
+		vsync-len = <2>;
+	};
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&lvds_encoder>;
+		};
+	};
+};

Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt

@@ -15,6 +15,10 @@ Required properties:
   "de_be1-lcd1"
   "de_be0-lcd0-hdmi"
   "de_be1-lcd1-hdmi"
+  "mixer0-lcd0"
+  "mixer0-lcd0-hdmi"
+  "mixer1-lcd1-hdmi"
+  "mixer1-lcd1-tve"
 
 Example:
 

Documentation/devicetree/bindings/dma/snps-dma.txt

@@ -64,6 +64,6 @@ Example:
 		reg = <0xe0000000 0x1000>;
 		interrupts = <0 35 0x4>;
 		dmas = <&dmahost 12 0 1>,
-			<&dmahost 13 0 1 0>;
+			<&dmahost 13 1 0>;
 		dma-names = "rx", "rx";
 	};

Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt

@@ -17,6 +17,7 @@ Required properties:
       + rockchip,rk3066-mali
       + rockchip,rk3188-mali
       + rockchip,rk3228-mali
+      + rockchip,rk3328-mali
       + stericsson,db8500-mali
 
   - reg: Physical base address and length of the GPU registers

Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt

@@ -12,6 +12,8 @@ Required properties:
 - clock-names: Must include the following entries:
   - mc: the module's clock input
 - interrupts: The interrupt outputs from the controller.
+
+Required properties for Tegra30, Tegra114, Tegra124, Tegra132 and Tegra210:
 - #iommu-cells: Should be 1. The single cell of the IOMMU specifier defines
   the SWGROUP of the master.
 

Documentation/devicetree/bindings/mfd/atmel-tcb.txt

@@ -0,0 +1,56 @@
+* Device tree bindings for Atmel Timer Counter Blocks
+- compatible: Should be "atmel,<chip>-tcb", "simple-mfd", "syscon".
+  <chip> can be "at91rm9200" or "at91sam9x5"
+- reg: Should contain registers location and length
+- #address-cells: has to be 1
+- #size-cells: has to be 0
+- interrupts: Should contain all interrupts for the TC block
+  Note that you can specify several interrupt cells if the TC
+  block has one interrupt per channel.
+- clock-names: tuple listing input clock names.
+	Required elements: "t0_clk", "slow_clk"
+	Optional elements: "t1_clk", "t2_clk"
+- clocks: phandles to input clocks.
+
+The TCB can expose multiple subdevices:
+ * a timer
+   - compatible: Should be "atmel,tcb-timer"
+   - reg: Should contain the TCB channels to be used. If the
+     counter width is 16 bits (at91rm9200-tcb), two consecutive
+     channels are needed. Else, only one channel will be used.
+
+Examples:
+
+One interrupt per TC block:
+	tcb0: timer@fff7c000 {
+		compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0xfff7c000 0x100>;
+		interrupts = <18 4>;
+		clocks = <&tcb0_clk>, <&clk32k>;
+		clock-names = "t0_clk", "slow_clk";
+
+		timer@0 {
+			compatible = "atmel,tcb-timer";
+			reg = <0>, <1>;
+		};
+
+		timer@2 {
+			compatible = "atmel,tcb-timer";
+			reg = <2>;
+		};
+	};
+
+One interrupt per TC channel in a TC block:
+	tcb1: timer@fffdc000 {
+		compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0xfffdc000 0x100>;
+		interrupts = <26 4>, <27 4>, <28 4>;
+		clocks = <&tcb1_clk>, <&clk32k>;
+		clock-names = "t0_clk", "slow_clk";
+	};
+
+

Documentation/devicetree/bindings/misc/nvidia,tegra186-misc.txt

@@ -0,0 +1,12 @@
+NVIDIA Tegra186 MISC register block
+
+The MISC register block found on Tegra186 SoCs contains registers that can be
+used to identify a given chip and various strapping options.
+
+Required properties:
+- compatible: Must be:
+  - Tegra186: "nvidia,tegra186-misc"
+- reg: Should contain 2 entries: The first entry gives the physical address
+       and length of the register region which contains revision and debug
+       features. The second entry specifies the physical address and length
+       of the register region indicating the strapping options.

Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt

@@ -9,6 +9,8 @@ Required properties for the root node:
 		      "amlogic,meson-gxbb-aobus-pinctrl"
 		      "amlogic,meson-gxl-periphs-pinctrl"
 		      "amlogic,meson-gxl-aobus-pinctrl"
+		      "amlogic,meson-axg-periphs-pinctrl"
+		      "amlogic,meson-axg-aobus-pinctrl"
  - reg: address and size of registers controlling irq functionality
 
 === GPIO sub-nodes ===

Documentation/devicetree/bindings/power/actions,owl-sps.txt

@@ -2,10 +2,12 @@ Actions Semi Owl Smart Power System (SPS)
 
 Required properties:
 - compatible          :  "actions,s500-sps" for S500
+                         "actions,s700-sps" for S700
 - reg                 :  Offset and length of the register set for the device.
 - #power-domain-cells :  Must be 1.
                          See macros in:
                           include/dt-bindings/power/owl-s500-powergate.h for S500
+                          include/dt-bindings/power/owl-s700-powergate.h for S700
 
 
 Example:

Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt

@@ -44,10 +44,10 @@ Example:
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			pgc_pcie_phy: power-domain@3 {
+			pgc_pcie_phy: power-domain@1 {
 				#power-domain-cells = <0>;
 
-				reg = <IMX7_POWER_DOMAIN_PCIE_PHY>;
+				reg = <1>;
 				power-supply = <&reg_1p0d>;
 			};
 		};

Documentation/devicetree/bindings/power/ti-smartreflex.txt

@@ -7,7 +7,7 @@ Required properties:
 
 compatible: Shall be one of the following:
 	    "ti,omap3-smartreflex-core"
-	    "ti,omap3-smartreflex-iva"
+	    "ti,omap3-smartreflex-mpu-iva"
 	    "ti,omap4-smartreflex-core"
 	    "ti,omap4-smartreflex-mpu"
 	    "ti,omap4-smartreflex-iva"