net: mediatek: sgmii: ensure the SGMII PHY is powered down on configu…

…ration

The code expect the PHY to be in power down which is only true after reset.
Allow changes of the SGMII parameters more than once.

Only power down when reconfiguring to avoid bouncing the link when there's
no reason to - based on code from Russell King.

There are cases when the SGMII_PHYA_PWD register contains 0x9 which
prevents SGMII from working. The SGMII still shows link but no traffic
can flow. Writing 0x0 to the PHYA_PWD register fix the issue. 0x0 was
taken from a good working state of the SGMII interface.

Fixes: 42c0384 ("net-next: mediatek: add support for MediaTek MT7622 SoC")
Suggested-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Alexander Couzens <[email protected]>
[ bmork: rebased and squashed into one patch ]
Reviewed-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Bjørn Mork <[email protected]>
Acked-by: Daniel Golle <[email protected]>
Tested-by: Daniel Golle <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>

drivers/net/ethernet/mediatek/mtk_eth_soc.h

@@ -1036,11 +1036,13 @@ struct mtk_soc_data {
  * @regmap:            The register map pointing at the range used to setup
  *                     SGMII modes
  * @ana_rgc3:          The offset refers to register ANA_RGC3 related to regmap
+ * @interface:         Currently configured interface mode
  * @pcs:               Phylink PCS structure
  */
 struct mtk_pcs {
 	struct regmap	*regmap;
 	u32             ana_rgc3;
+	phy_interface_t	interface;
 	struct phylink_pcs pcs;
 };
 

drivers/net/ethernet/mediatek/mtk_sgmii.c

@@ -43,11 +43,6 @@ static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
 	int advertise, link_timer;
 	bool changed, use_an;
 
-	if (interface == PHY_INTERFACE_MODE_2500BASEX)
-		rgc3 = RG_PHY_SPEED_3_125G;
-	else
-		rgc3 = 0;
-
 	advertise = phylink_mii_c22_pcs_encode_advertisement(interface,
 							     advertising);
 	if (advertise < 0)
@@ -88,9 +83,22 @@ static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
 		bmcr = 0;
 	}
 
-	/* Configure the underlying interface speed */
-	regmap_update_bits(mpcs->regmap, mpcs->ana_rgc3,
-			   RG_PHY_SPEED_3_125G, rgc3);
+	if (mpcs->interface != interface) {
+		/* PHYA power down */
+		regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL,
+				   SGMII_PHYA_PWD, SGMII_PHYA_PWD);
+
+		if (interface == PHY_INTERFACE_MODE_2500BASEX)
+			rgc3 = RG_PHY_SPEED_3_125G;
+		else
+			rgc3 = 0;
+
+		/* Configure the underlying interface speed */
+		regmap_update_bits(mpcs->regmap, mpcs->ana_rgc3,
+				   RG_PHY_SPEED_3_125G, rgc3);
+
+		mpcs->interface = interface;
+	}
 
 	/* Update the advertisement, noting whether it has changed */
 	regmap_update_bits_check(mpcs->regmap, SGMSYS_PCS_ADVERTISE,
@@ -108,9 +116,17 @@ static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
 	regmap_update_bits(mpcs->regmap, SGMSYS_PCS_CONTROL_1,
 			   SGMII_AN_RESTART | SGMII_AN_ENABLE, bmcr);
 
-	/* Release PHYA power down state */
-	regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL,
-			   SGMII_PHYA_PWD, 0);
+	/* Release PHYA power down state
+	 * Only removing bit SGMII_PHYA_PWD isn't enough.
+	 * There are cases when the SGMII_PHYA_PWD register contains 0x9 which
+	 * prevents SGMII from working. The SGMII still shows link but no traffic
+	 * can flow. Writing 0x0 to the PHYA_PWD register fix the issue. 0x0 was
+	 * taken from a good working state of the SGMII interface.
+	 * Unknown how much the QPHY needs but it is racy without a sleep.
+	 * Tested on mt7622 & mt7986.
+	 */
+	usleep_range(50, 100);
+	regmap_write(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL, 0);
 
 	return changed;
 }
@@ -171,6 +187,7 @@ int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *r, u32 ana_rgc3)
 			return PTR_ERR(ss->pcs[i].regmap);
 
 		ss->pcs[i].pcs.ops = &mtk_pcs_ops;
+		ss->pcs[i].interface = PHY_INTERFACE_MODE_NA;
 	}
 
 	return 0;