Merge tag 'rtc-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/…

…abelloni/linux

Pull RTC updates from Alexandre Belloni:
 "There is an unusual amount of new drivers this cycle, and this
  explains the number of insertions.

  Other than that, the changes are the usual fixes and feature addition.

  Subsystem updates:
   - new quartz-load-femtofarads DT property for quartz load capacitance
   - remove rtc_class_ops.read_callback

  New drivers:
   - Abracon AB-RTCMC-32.768kHz-EOZ9
   - Amlogic Meson RTC
   - Cadence RTC IP
   - Microcrystal RV3028
   - Whwave sd3078

  Driver updates:
   - cmos: ignore bogus century byte
   - ds1307: rework rx8130 support
   - isl1208: add isl1209 support, nvmem support
   - rs5C372: report invalid time when the oscillator stopped
   - rx8581: add rx8571 support"

* tag 'rtc-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (66 commits)
  rtc: pic32: convert to SPDX identifier
  rtc: pic32: let the core handle range
  rtc: pic32: convert to devm_rtc_allocate_device
  rtc: update my email address
  rtc: rv8803: convert to SPDX identifier
  rtc: rv8803: let the core handle range
  rtc: tx4939: convert to SPDX identifier
  rtc: tx4939: use .set_time
  rtc: tx4939: switch to rtc_time64_to_tm/rtc_tm_to_time64
  rtc: tx4939: set range
  rtc: tx4939: remove useless test
  rtc: zynqmp: let the core handle range
  rtc: zynqmp: fix possible race condition
  rtc: imx-sc: use rtc_time64_to_tm
  rtc: rx8581: Add support for Epson rx8571 RTC
  dt-bindings: rtc: add rx8571 compatible
  rtc: pcf85063: remove dead code
  rtc: remove rtc_class_ops.read_callback
  rtc: add AB-RTCMC-32.768kHz-EOZ9 RTC support
  dt-bindings: rtc: add ABEOZ9
  ...

Documentation/devicetree/bindings/property-units.txt

@@ -31,6 +31,7 @@ Electricity
 -microwatt-hours: micro Watt-hours
 -microvolt	: micro volts
 -picofarads	: picofarads
+-femtofarads	: femtofarads
 
 Temperature
 ----------------------------------------

Documentation/devicetree/bindings/rtc/abracon,abx80x.txt

@@ -16,6 +16,7 @@ Required properties:
         "abracon,ab1803"
         "abracon,ab1804"
         "abracon,ab1805"
+        "microcrystal,rv1805"
 	Using "abracon,abx80x" will enable chip autodetection.
  - "reg": I2C bus address of the device
 

Documentation/devicetree/bindings/rtc/cdns,rtc.txt

@@ -0,0 +1,25 @@
+Cadence Real Time Clock
+
+The Cadence RTC controller with date, time and alarm capabilities.
+The alarm may wake the system from low-power state.
+
+Required properties:
+- compatible: Should be "cdns,rtc-r109v3"
+- reg: Specifies base physical address and size of the register area.
+- interrupts: A single interrupt specifier.
+- clocks: Must contain two entries:
+	- pclk: APB registers clock
+	- ref_clk: reference 1Hz or 100Hz clock, depending on IP configuration
+	See ../clocks/clock-bindings.txt for details.
+
+Example:
+        rtc0: rtc@fd080000 {
+        	compatible = "cdns,rtc-r109v3";
+        	reg = <0xfd080000 0x1000>;
+
+        	clock-names = "pclk", "ref_clk";
+        	clocks = <&sysclock>, <&refclock>;
+
+        	interrupt-parent = <&gic>;
+        	interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>;
+        };

Documentation/devicetree/bindings/rtc/isil,isl1208.txt

@@ -0,0 +1,38 @@
+Intersil ISL1209/19 I2C RTC/Alarm chip with event in
+
+ISL12X9 have additional pins EVIN and #EVDET for tamper detection, while the
+ISL1208 and ISL1218 do not.  They are all use the same driver with the bindings
+described here, with chip specific properties as noted.
+
+Required properties supported by the device:
+ - "compatible": Should be one of the following:
+		- "isil,isl1208"
+		- "isil,isl1209"
+		- "isil,isl1218"
+		- "isil,isl1219"
+ - "reg": I2C bus address of the device
+
+Optional properties:
+ - "interrupt-names": list which may contains "irq" and "evdet"
+	evdet applies to isl1209 and isl1219 only
+ - "interrupts": list of interrupts for "irq" and "evdet"
+	evdet applies to isl1209 and isl1219 only
+ - "isil,ev-evienb": Enable or disable internal pull on EVIN pin
+	Applies to isl1209 and isl1219 only
+	Possible values are 0 and 1
+	Value 0 enables internal pull-up on evin pin, 1 disables it.
+	Default will leave the non-volatile configuration of the pullup
+	as is.
+
+Example isl1219 node with #IRQ pin connected to SoC gpio1 pin12 and #EVDET pin
+connected to SoC gpio2 pin 24 and internal pull-up enabled in EVIN pin.
+
+	isl1219: rtc@68 {
+		compatible = "isil,isl1219";
+		reg = <0x68>;
+		interrupt-names = "irq", "evdet";
+		interrupts-extended = <&gpio1 12 IRQ_TYPE_EDGE_FALLING>,
+			<&gpio2 24 IRQ_TYPE_EDGE_FALLING>;
+		isil,ev-evienb = <1>;
+	};
+

Documentation/devicetree/bindings/rtc/nxp,pcf85063.txt

@@ -0,0 +1,18 @@
+* NXP PCF85063 Real Time Clock
+
+Required properties:
+- compatible: Should contain "nxp,pcf85063".
+- reg: I2C address for chip.
+
+Optional property:
+- quartz-load-femtofarads: The capacitive load of the quartz(x-tal),
+  expressed in femto Farad (fF). Valid values are 7000 and 12500.
+  Default value (if no value is specified) is 7000fF.
+
+Example:
+
+pcf85063: rtc@51 {
+	compatible = "nxp,pcf85063";
+	reg = <0x51>;
+	quartz-load-femtofarads = <12500>;
+};

Documentation/devicetree/bindings/rtc/nxp,pcf8523.txt

@@ -0,0 +1,18 @@
+* NXP PCF8523 Real Time Clock
+
+Required properties:
+- compatible: Should contain "nxp,pcf8523".
+- reg: I2C address for chip.
+
+Optional property:
+- quartz-load-femtofarads: The capacitive load of the quartz(x-tal),
+  expressed in femto Farad (fF). Valid values are 7000 and 12500.
+  Default value (if no value is specified) is 12500fF.
+
+Example:
+
+pcf8523: rtc@68 {
+	compatible = "nxp,pcf8523";
+	reg = <0x68>;
+	quartz-load-femtofarads = <7000>;
+};

Documentation/devicetree/bindings/rtc/rtc-meson.txt

@@ -0,0 +1,35 @@
+* Amlogic Meson6, Meson8, Meson8b and Meson8m2 RTC
+
+Required properties:
+- compatible: should be one of the following describing the hardware:
+	* "amlogic,meson6-rtc"
+	* "amlogic,meson8-rtc"
+	* "amlogic,meson8b-rtc"
+	* "amlogic,meson8m2-rtc"
+
+- reg: physical register space for the controller's memory mapped registers.
+- interrupts: the interrupt line of the RTC block.
+- clocks: reference to the external 32.768kHz crystal oscillator.
+- vdd-supply: reference to the power supply of the RTC block.
+- resets: reset controller reference to allow reset of the controller
+
+Optional properties for the battery-backed non-volatile memory:
+- #address-cells: should be 1 to address the battery-backed non-volatile memory
+- #size-cells: should be 1 to reference the battery-backed non-volatile memory
+
+Optional child nodes:
+- see ../nvmem/nvmem.txt
+
+Example:
+
+	rtc: rtc@740 {
+		compatible = "amlogic,meson6-rtc";
+		reg = <0x740 0x14>;
+		interrupts = <GIC_SPI 72 IRQ_TYPE_EDGE_RISING>;
+		clocks = <&rtc32k_xtal>;
+		vdd-supply = <&rtc_vdd>;
+		resets = <&reset RESET_RTC>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};

Documentation/devicetree/bindings/rtc/rtc.txt

@@ -21,12 +21,16 @@ Optional properties
 The following properties may not be supported by all drivers. However, if a
 driver wants to support one of the below features, it should adapt the bindings
 below.
-- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given
-                          if trickle charger should be enabled
-- trickle-diode-disable : Do not use internal trickle charger diode Should be
-                          given if internal trickle charger diode should be
-                          disabled
-- wakeup-source :         Enables wake up of host system on alarm
+- trickle-resistor-ohms :   Selected resistor for trickle charger. Should be given
+                            if trickle charger should be enabled
+- trickle-diode-disable :   Do not use internal trickle charger diode Should be
+                            given if internal trickle charger diode should be
+                            disabled
+- wakeup-source :           Enables wake up of host system on alarm
+- quartz-load-femtofarads : The capacitive load of the quartz(x-tal),
+                            expressed in femto Farad (fF).
+                            The default value shall be listed (if optional),
+                            and likewise all valid values.
 
 Trivial RTCs
 ------------
@@ -39,21 +43,23 @@ possibly an interrupt line.
 Compatible		Vendor / Chip
 ==========		=============
 abracon,abb5zes3	AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface
+abracon,abeoz9		AB-RTCMC-32.768kHz-EOZ9: Real Time Clock/Calendar Module with I2C Interface
 dallas,ds1374		I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output
 dallas,ds1672		Dallas DS1672 Real-time Clock
 dallas,ds3232		Extremely Accurate I²C RTC with Integrated Crystal and SRAM
 epson,rx8010		I2C-BUS INTERFACE REAL TIME CLOCK MODULE
+epson,rx8571		I2C-BUS INTERFACE REAL TIME CLOCK MODULE with Battery Backed RAM
 epson,rx8581		I2C-BUS INTERFACE REAL TIME CLOCK MODULE
 emmicro,em3027		EM Microelectronic EM3027 Real-time Clock
 isil,isl1208		Intersil ISL1208 Low Power RTC with Battery Backed SRAM
 isil,isl1218		Intersil ISL1218 Low Power RTC with Battery Backed SRAM
 isil,isl12022		Intersil ISL12022 Real-time Clock
+microcrystal,rv3028	Real Time Clock Module with I2C-Bus
 microcrystal,rv3029	Real Time Clock Module with I2C-Bus
+microcrystal,rv8523	Real Time Clock
 nxp,pcf2127		Real-time clock
 nxp,pcf2129		Real-time clock
-nxp,pcf8523		Real-time Clock
 nxp,pcf8563		Real-time clock/calendar
-nxp,pcf85063		Tiny Real-Time Clock
 pericom,pt7c4338	Real-time Clock Module
 ricoh,r2025sd		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
 ricoh,r2221tl		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
@@ -62,3 +68,4 @@ ricoh,rs5c372b		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
 ricoh,rv5c386		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
 ricoh,rv5c387a		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
 sii,s35390a		2-wire CMOS real-time clock
+whwave,sd3078		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -439,6 +439,7 @@ vot	Vision Optical Technology Co., Ltd.
 wd	Western Digital Corp.
 wetek	WeTek Electronics, limited.
 wexler	Wexler
+whwave  Shenzhen whwave Electronics, Inc.
 wi2wi	Wi2Wi, Inc.
 winbond Winbond Electronics corp.
 winstar	Winstar Display Corp.

MAINTAINERS

@@ -16697,6 +16697,12 @@ L:	[email protected]
 S:	Maintained
 F:	drivers/gpio/gpio-wcove.c
 
+WHWAVE RTC DRIVER
+M:	Dianlong Li <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	drivers/rtc/rtc-sd3078.c
+
 WIIMOTE HID DRIVER
 M:	David Herrmann <[email protected]>
 L:	[email protected]

drivers/rtc/Kconfig

@@ -185,6 +185,16 @@ config RTC_DRV_ABB5ZES3
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-ab-b5ze-s3.
 
+config RTC_DRV_ABEOZ9
+	select REGMAP_I2C
+	tristate "Abracon AB-RTCMC-32.768kHz-EOZ9"
+	help
+	  If you say yes here you get support for the Abracon
+	  AB-RTCMC-32.768kHz-EOA9 I2C RTC chip.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called rtc-ab-e0z9.
+
 config RTC_DRV_ABX80X
 	tristate "Abracon ABx80x"
 	select WATCHDOG_CORE if WATCHDOG
@@ -601,9 +611,10 @@ config RTC_DRV_RX8010
 	  will be called rtc-rx8010.
 
 config RTC_DRV_RX8581
-	tristate "Epson RX-8581"
+	tristate "Epson RX-8571/RX-8581"
 	help
-	  If you say yes here you will get support for the Epson RX-8581.
+	  If you say yes here you will get support for the Epson RX-8571/
+	  RX-8581.
 
 	  This driver can also be built as a module. If so the module
 	  will be called rtc-rx8581.
@@ -626,6 +637,15 @@ config RTC_DRV_EM3027
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-em3027.
 
+config RTC_DRV_RV3028
+	tristate "Micro Crystal RV3028"
+	help
+	  If you say yes here you get support for the Micro Crystal
+	  RV3028.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called rtc-rv3028.
+
 config RTC_DRV_RV8803
 	tristate "Micro Crystal RV8803, Epson RX8900"
 	help
@@ -646,6 +666,15 @@ config RTC_DRV_S5M
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-s5m.
 
+config RTC_DRV_SD3078
+    tristate "ZXW Crystal SD3078"
+    help
+      If you say yes here you get support for the ZXW Crystal
+      SD3078 RTC chips.
+
+      This driver can also be built as a module. If so, the module
+      will be called rtc-sd3078
+
 endif # I2C
 
 comment "SPI RTC drivers"
@@ -1285,6 +1314,17 @@ config RTC_DRV_IMXDI
 	   This driver can also be built as a module, if so, the module
 	   will be called "rtc-imxdi".
 
+config RTC_DRV_MESON
+	tristate "Amlogic Meson RTC"
+	depends on (ARM && ARCH_MESON) || COMPILE_TEST
+	select REGMAP_MMIO
+	help
+	   Support for the RTC block on the Amlogic Meson6, Meson8, Meson8b
+	   and Meson8m2 SoCs.
+
+	   This driver can also be built as a module, if so, the module
+	   will be called "rtc-meson".
+
 config RTC_DRV_OMAP
 	tristate "TI OMAP Real Time Clock"
 	depends on ARCH_OMAP || ARCH_DAVINCI || COMPILE_TEST
@@ -1508,6 +1548,16 @@ config RTC_DRV_ARMADA38X
 	  This driver can also be built as a module. If so, the module
 	  will be called armada38x-rtc.
 
+config RTC_DRV_CADENCE
+	tristate "Cadence RTC driver"
+	depends on OF && HAS_IOMEM
+	help
+	  If you say Y here you will get access to Cadence RTC IP
+	  found on certain SOCs.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called rtc-cadence.
+
 config RTC_DRV_FTRTC010
 	tristate "Faraday Technology FTRTC010 RTC"
 	depends on HAS_IOMEM
@@ -1679,6 +1729,7 @@ config RTC_DRV_SNVS
 
 config RTC_DRV_IMX_SC
 	depends on IMX_SCU
+	depends on HAVE_ARM_SMCCC
 	tristate "NXP i.MX System Controller RTC support"
 	help
 	   If you say yes here you get support for the NXP i.MX System
@@ -1795,8 +1846,7 @@ comment "HID Sensor RTC drivers"
 config RTC_DRV_HID_SENSOR_TIME
 	tristate "HID Sensor Time"
 	depends on USB_HID
-	select IIO
-	select HID_SENSOR_HUB
+	depends on HID_SENSOR_HUB && IIO
 	select HID_SENSOR_IIO_COMMON
 	help
 	  Say yes here to build support for the HID Sensors of type Time.