arm64: dts: imx8mq-librem5: describe the selfie cam

Enable the CSI1 MIPI RX controller and CSI1 bridge on the SoC. Describe
the Librem 5 front-facing camera, connected to the CSI1 MIPI.

the following sets formats, streams 10 frames and saves one:

	#!/bin/bash
	WIDTH=1632
	HEIGHT=1224
	SKIP=10

	media-ctl -d "platform:30a90000.csi" --set-v4l2 "'csi':0 [fmt:SGBRG10/${WIDTH}x${HEIGHT} colorspace:raw]"
	media-ctl -d "platform:30a90000.csi" --set-v4l2 "'imx8mq-mipi-csi2 30a70000.csi':0 [fmt:SGBRG10/${WIDTH}x${HEIGHT} colorspace:raw]"
	media-ctl -d "platform:30a90000.csi" --set-v4l2 "'hi846 2-0020':0 [fmt:SGBRG10/${WIDTH}x${HEIGHT} colorspace:raw]"
	media-ctl -d "platform:30a90000.csi" -l "'hi846 2-0020':0 -> 'imx8mq-mipi-csi2 30a70000.csi':0 [1]"
	v4l2-ctl -d "/dev/v4l/by-path/platform-30a90000.csi-video-index0" --set-fmt-video=width=${WIDTH},height=${HEIGHT},pixelformat=GB16 --stream-mmap --stream-to=$WIDTH.raw --stream-skip=$SKIP --stream-count=1

Signed-off-by: Martin Kepplinger <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>

arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi

@@ -272,6 +272,10 @@
 	cpu-supply = <&buck2_reg>;
 };
 
+&csi1 {
+	status = "okay";
+};
+
 &ddrc {
 	operating-points-v2 = <&ddrc_opp_table>;
 
@@ -1007,6 +1011,31 @@
 		>;
 	};
 
+	camera_front: camera@20 {
+		compatible = "hynix,hi846";
+		reg = <0x20>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_csi1>;
+		clocks = <&clk IMX8MQ_CLK_CLKO2>;
+		assigned-clocks = <&clk IMX8MQ_CLK_CLKO2>;
+		assigned-clock-rates = <25000000>;
+		reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+		vdda-supply = <&reg_vcam_2v8>;
+		vddd-supply = <&reg_vcam_1v2>;
+		vddio-supply = <&reg_csi_1v8>;
+		rotation = <90>;
+		orientation = <0>;
+
+		port {
+			camera1_ep: endpoint {
+				data-lanes = <1 2>;
+				link-frequencies = /bits/ 64
+					<80000000 200000000 300000000>;
+				remote-endpoint = <&mipi1_sensor_ep>;
+			};
+		};
+	};
+
 	backlight@36 {
 		compatible = "ti,lm36922";
 		reg = <0x36>;
@@ -1080,6 +1109,23 @@
 	status = "okay";
 };
 
+&mipi_csi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			mipi1_sensor_ep: endpoint {
+				remote-endpoint = <&camera1_ep>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
 &mipi_dsi {
 	#address-cells = <1>;
 	#size-cells = <0>;