Merge tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/gi…

…t/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Decrease polling rate for erase/trim/discard
   - Allow non-sleeping GPIOs for card detect
   - Improve mmc block removal path
   - Enable support for mmc_sw_reset() for SDIO cards
   - Add mmc_sw_reset() to allow users to do a soft reset of the card
   - Allow power delay to be tunable via DT
   - Allow card detect debounce delay to be tunable via DT
   - Enable new quirk to limit clock rate for Marvell 8887 chip
   - Don't show eMMC RPMB and BOOT areas in /proc/partitions
   - Add capability to avoid 3.3V signaling for fragile HWs

  MMC host:
   - Improve/fixup support for handle highmem pages
   - Remove depends on HAS_DMA in case of platform dependency
   - mvsdio: Enable support for erase/trim/discard
   - rtsx_usb: Enable support for erase/trim/discard
   - renesas_sdhi: Fix WP logic regressions
   - renesas_sdhi: Add r8a77965 support
   - renesas_sdhi: Add R8A77980 to whitelist
   - meson: Add optional support for device reset
   - meson: Add support for the Meson-AXG platform
   - dw_mmc: Add new driver for BlueField DW variant
   - mediatek: Add support for 64G DRAM DMA
   - sunxi: Deploy runtime PM support
   - jz4740: Add support for JZ4780
   - jz4740: Enable support for DT based platforms
   - sdhci: Various improvement to timeout handling
   - sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
   - sdhci-omap: Add support for controller in k2g SoC
   - sdhci-omap: Add workarounds for a couple of Erratas
   - sdhci-omap: Enable support for generic sdhci DT properties
   - sdhci-cadence: Re-send tune request to deal with errata
   - sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
   - sdhci-pci: Avoid 3.3V signaling on some NI 904x
   - sdhci-esdhc-imx: Use watermark levels for PIO access
   - sdhci-msm: Improve card detection handling
   - sdhci-msm: Add support voltage pad switching"

* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
  mmc: renesas_sdhi: really fix WP logic regressions
  mmc: mvsdio: Enable MMC_CAP_ERASE
  mmc: mvsdio: Respect card busy time out from mmc core
  mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
  mmc: sunxi: Use ifdef rather than __maybe_unused
  mmc: mxmmc: Use ifdef rather than __maybe_unused
  mmc: mxmmc: include linux/highmem.h
  mmc: sunxi: mark PM functions as __maybe_unused
  mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
  mmc: au1xmmc: handle highmem pages
  mmc: Allow non-sleeping GPIO cd
  mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
  mmc: sd: Define name for default speed dtr
  mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
  mmc: sdhci-xenon: use match_string() helper
  mmc: wbsd: handle highmem pages
  mmc: ushc: handle highmem pages
  mmc: mxcmmc: handle highmem pages
  mmc: atmel-mci: use sg_copy_{from,to}_buffer
  mmc: android-goldfish: use sg_copy_{from,to}_buffer
  ...

Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt

@@ -12,13 +12,15 @@ Required properties:
   - "amlogic,meson-gxbb-mmc"
   - "amlogic,meson-gxl-mmc"
   - "amlogic,meson-gxm-mmc"
+  - "amlogic,meson-axg-mmc"
 - clocks     : A list of phandle + clock-specifier pairs for the clocks listed in clock-names.
 - clock-names: Should contain the following:
 	"core" - Main peripheral bus clock
 	"clkin0" - Parent clock of internal mux
 	"clkin1" - Other parent clock of internal mux
   The driver has an internal mux clock which switches between clkin0 and clkin1 depending on the
   clock rate requested by the MMC core.
+- resets     : phandle of the internal reset line
 
 Example:
 
@@ -29,4 +31,5 @@ Example:
 		clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>;
 		clock-names = "core", "clkin0", "clkin1";
 		pinctrl-0 = <&emmc_pins>;
+		resets = <&reset RESET_SD_EMMC_A>;
 	};

Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt

@@ -0,0 +1,29 @@
+* Mellanox Bluefield SoC specific extensions to the Synopsys Designware
+  Mobile Storage Host Controller
+
+Read synopsys-dw-mshc.txt for more details
+
+The Synopsys designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core Synopsys dw mshc controller properties described
+by synopsys-dw-mshc.txt and the properties used by the Mellanox Bluefield SoC
+specific extensions to the Synopsys Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be one of the following.
+  - "mellanox,bluefield-dw-mshc": for controllers with Mellanox Bluefield SoC
+    specific extensions.
+
+Example:
+
+	/* Mellanox Bluefield SoC MMC */
+	mmc@6008000 {
+		compatible = "mellanox,bluefield-dw-mshc";
+		reg = <0x6008000 0x400>;
+		interrupts = <32>;
+		fifo-depth = <0x100>;
+		clock-frequency = <24000000>;
+		bus-width = <8>;
+		cap-mmc-highspeed;
+	};

Documentation/devicetree/bindings/mmc/jz4740.txt

@@ -0,0 +1,38 @@
+* Ingenic JZ47xx MMC controllers
+
+This file documents the device tree properties used for the MMC controller in
+Ingenic JZ4740/JZ4780 SoCs. These are in addition to the core MMC properties
+described in mmc.txt.
+
+Required properties:
+- compatible: Should be one of the following:
+  - "ingenic,jz4740-mmc" for the JZ4740
+  - "ingenic,jz4780-mmc" for the JZ4780
+- reg: Should contain the MMC controller registers location and length.
+- interrupts: Should contain the interrupt specifier of the MMC controller.
+- clocks: Clock for the MMC controller.
+
+Optional properties:
+- dmas: List of DMA specifiers with the controller specific format
+        as described in the generic DMA client binding. A tx and rx
+        specifier is required.
+- dma-names: RX and TX  DMA request names.
+        Should be "rx" and "tx", in that order.
+
+For additional details on DMA client bindings see ../dma/dma.txt.
+
+Example:
+
+mmc0: mmc@13450000 {
+	compatible = "ingenic,jz4780-mmc";
+	reg = <0x13450000 0x1000>;
+
+	interrupt-parent = <&intc>;
+	interrupts = <37>;
+
+	clocks = <&cgu JZ4780_CLK_MSC0>;
+	clock-names = "mmc";
+
+	dmas = <&dma JZ4780_DMA_MSC0_RX 0xffffffff>, <&dma JZ4780_DMA_MSC0_TX 0xffffffff>;
+	dma-names = "rx", "tx";
+};

Documentation/devicetree/bindings/mmc/mmc.txt

@@ -19,6 +19,8 @@ Optional properties:
 - wp-gpios: Specify GPIOs for write protection, see gpio binding
 - cd-inverted: when present, polarity on the CD line is inverted. See the note
   below for the case, when a GPIO is used for the CD line
+- cd-debounce-delay-ms: Set delay time before detecting card after card insert interrupt.
+  It's only valid when cd-gpios is present.
 - wp-inverted: when present, polarity on the WP line is inverted. See the note
   below for the case, when a GPIO is used for the WP line
 - disable-wp: When set no physical WP line is present. This property should
@@ -56,6 +58,10 @@ Optional properties:
 - fixed-emmc-driver-type: for non-removable eMMC, enforce this driver type.
   The value <n> is the driver type as specified in the eMMC specification
   (table 206 in spec version 5.1).
+- post-power-on-delay-ms : It was invented for MMC pwrseq-simple which could
+  be referred to mmc-pwrseq-simple.txt. But now it's reused as a tunable delay
+  waiting for I/O signalling and card power supply to be stable, regardless of
+  whether pwrseq-simple is used. Default to 10ms if no available.
 
 *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
 polarity properties, we have to fix the meaning of the "normal" and "inverted"

Documentation/devicetree/bindings/mmc/sdhci-omap.txt

@@ -4,7 +4,14 @@ Refer to mmc.txt for standard MMC bindings.
 
 Required properties:
 - compatible: Should be "ti,dra7-sdhci" for DRA7 and DRA72 controllers
+	      Should be "ti,k2g-sdhci" for K2G
 - ti,hwmods: Must be "mmc<n>", <n> is controller instance starting 1
+	     (Not required for K2G).
+- pinctrl-names: Should be subset of "default", "hs", "sdr12", "sdr25", "sdr50",
+		 "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104",
+		 "ddr_1_8v-rev11", "ddr_1_8v" or "ddr_3_3v", "hs200_1_8v-rev11",
+		 "hs200_1_8v",
+- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt
 
 Example:
 	mmc1: mmc@4809c000 {

Documentation/devicetree/bindings/mmc/tmio_mmc.txt

@@ -26,6 +26,8 @@ Required properties:
 		"renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC
 		"renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC
 		"renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC
+		"renesas,sdhi-r8a77965" - SDHI IP on R8A77965 SoC
+		"renesas,sdhi-r8a77980" - SDHI IP on R8A77980 SoC
 		"renesas,sdhi-r8a77995" - SDHI IP on R8A77995 SoC
 		"renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller
 		"renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller

arch/mips/boot/dts/ingenic/ci20.dts

@@ -36,6 +36,28 @@
 	clock-frequency = <48000000>;
 };
 
+&mmc0 {
+	status = "okay";
+
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mmc0>;
+
+	cd-gpios = <&gpf 20 GPIO_ACTIVE_LOW>;
+};
+
+&mmc1 {
+	status = "okay";
+
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mmc1>;
+};
+
 &uart0 {
 	status = "okay";
 
@@ -203,4 +225,16 @@
 		groups = "nemc-cs6";
 		bias-disable;
 	};
+
+	pins_mmc0: mmc0 {
+		function = "mmc0";
+		groups = "mmc0-1bit-e", "mmc0-4bit-e";
+		bias-disable;
+	};
+
+	pins_mmc1: mmc1 {
+		function = "mmc1";
+		groups = "mmc1-1bit-d", "mmc1-4bit-d";
+		bias-disable;
+	};
 };

arch/mips/boot/dts/ingenic/jz4780.dtsi

@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <dt-bindings/clock/jz4780-cgu.h>
+#include <dt-bindings/dma/jz4780-dma.h>
 
 / {
 	#address-cells = <1>;
@@ -241,6 +242,57 @@
 		status = "disabled";
 	};
 
+	dma: dma@13420000 {
+		compatible = "ingenic,jz4780-dma";
+		reg = <0x13420000 0x10000>;
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		clocks = <&cgu JZ4780_CLK_PDMA>;
+	};
+
+	mmc0: mmc@13450000 {
+		compatible = "ingenic,jz4780-mmc";
+		reg = <0x13450000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <37>;
+
+		clocks = <&cgu JZ4780_CLK_MSC0>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+		dmas = <&dma JZ4780_DMA_MSC0_RX 0xffffffff>,
+		       <&dma JZ4780_DMA_MSC0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	mmc1: mmc@13460000 {
+		compatible = "ingenic,jz4780-mmc";
+		reg = <0x13460000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <36>;
+
+		clocks = <&cgu JZ4780_CLK_MSC1>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+		dmas = <&dma JZ4780_DMA_MSC1_RX 0xffffffff>,
+		       <&dma JZ4780_DMA_MSC1_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
 	bch: bch@134d0000 {
 		compatible = "ingenic,jz4780-bch";
 		reg = <0x134d0000 0x10000>;

arch/mips/configs/ci20_defconfig

@@ -104,10 +104,14 @@ CONFIG_REGULATOR_FIXED_VOLTAGE=y
 # CONFIG_HID is not set
 # CONFIG_USB_SUPPORT is not set
 CONFIG_MMC=y
+CONFIG_MMC_JZ4740=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_MEMORY=y
+CONFIG_EXT4_FS=y
 # CONFIG_DNOTIFY is not set
 CONFIG_PROC_KCORE=y
 # CONFIG_PROC_PAGE_MONITOR is not set

drivers/mmc/core/block.c

@@ -2351,7 +2351,8 @@ static struct mmc_blk_data *mmc_blk_alloc_req(struct mmc_card *card,
 	set_disk_ro(md->disk, md->read_only || default_ro);
 	md->disk->flags = GENHD_FL_EXT_DEVT;
 	if (area_type & (MMC_BLK_DATA_AREA_RPMB | MMC_BLK_DATA_AREA_BOOT))
-		md->disk->flags |= GENHD_FL_NO_PART_SCAN;
+		md->disk->flags |= GENHD_FL_NO_PART_SCAN
+				   | GENHD_FL_SUPPRESS_PARTITION_INFO;
 
 	/*
 	 * As discussed on lkml, GENHD_FL_REMOVABLE should:
@@ -2965,9 +2966,11 @@ static void mmc_blk_remove(struct mmc_card *card)
 	mmc_blk_remove_debugfs(card, md);
 	mmc_blk_remove_parts(card, md);
 	pm_runtime_get_sync(&card->dev);
-	mmc_claim_host(card->host);
-	mmc_blk_part_switch(card, md->part_type);
-	mmc_release_host(card->host);
+	if (md->part_curr != md->part_type) {
+		mmc_claim_host(card->host);
+		mmc_blk_part_switch(card, md->part_type);
+		mmc_release_host(card->host);
+	}
 	if (card->type != MMC_TYPE_SD_COMBO)
 		pm_runtime_disable(&card->dev);
 	pm_runtime_put_noidle(&card->dev);

drivers/mmc/core/card.h

@@ -149,6 +149,12 @@ static inline void __maybe_unused remove_quirk(struct mmc_card *card, int data)
 	card->quirks &= ~data;
 }
 
+static inline void __maybe_unused add_limit_rate_quirk(struct mmc_card *card,
+						       int data)
+{
+	card->quirk_max_rate = data;
+}
+
 /*
  * Quirk add/remove for MMC products.
  */