boards: mimxrt1062_fmurt6: remove regulator-fixed pinctrl entries

regulator-fixed is not a pinctrl-device, so these entries were invalid (and not used). Signed-off-by: Gerard Marull-Paretas <[email protected]>
phan-uy-vu · Sep 27, 2023 · 078d6c9 · 078d6c9
1 parent 7ff5088
commit 078d6c9
Show file tree

Hide file tree

Showing 2 changed files with 0 additions and 26 deletions.
diff --git a/boards/arm/mimxrt1062_fmurt6/mimxrt1062_fmurt6-pinctrl.dtsi b/boards/arm/mimxrt1062_fmurt6/mimxrt1062_fmurt6-pinctrl.dtsi
@@ -59,20 +59,6 @@
 		};
 	};
 
-	pinmux_sensor: pinmux_sensor {
-		group0	{
-			pinmux = <&iomuxc_gpio_emc_13_gpio4_io13>,
-				<&iomuxc_gpio_emc_09_gpio4_io09>,
-				<&iomuxc_gpio_emc_06_gpio4_io06>,
-				<&iomuxc_gpio_emc_41_gpio3_io27>,
-				<&iomuxc_gpio_ad_b0_00_gpio1_io00>,
-				<&iomuxc_snvs_pmic_on_req_gpio5_io01>;
-			drive-strength = "r0-7";
-			bias-pull-up;
-			slew-rate = "fast";
-		};
-	};
-
 	pinmux_flexcan1: pinmux_flexcan1 {
 		group0 {
 			pinmux = <&iomuxc_gpio_ad_b1_08_flexcan1_tx>,

diff --git a/boards/arm/mimxrt1062_fmurt6/mimxrt1062_fmurt6.dts b/boards/arm/mimxrt1062_fmurt6/mimxrt1062_fmurt6.dts
@@ -51,8 +51,6 @@
 
 	/* This regulator controls VDD_3V3_SD_CARD onboard supply */
 	reg-3v3-sdcard {
-		pinctrl-0 = <&pinmux_sensor>;
-		pinctrl-names = "default";
 		compatible = "regulator-fixed";
 		regulator-name = "reg-3v3-sdcard";
 		enable-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
@@ -62,8 +60,6 @@
 
 	/* This regulator controls VDD_5V_PERIPH onboard supply */
 	reg-5v-periph {
-		pinctrl-0 = <&pinmux_sensor>;
-		pinctrl-names = "default";
 		compatible = "regulator-fixed";
 		regulator-name = "reg-5v-periph";
 		enable-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
@@ -73,8 +69,6 @@
 
 	/* This regulator controls VDD_5V_HIPOWER onboard supply */
 	reg-5v-hipower {
-		pinctrl-0 = <&pinmux_sensor>;
-		pinctrl-names = "default";
 		compatible = "regulator-fixed";
 		regulator-name = "reg-5v-hipower";
 		enable-gpios = <&gpio4 6 GPIO_ACTIVE_LOW>;
@@ -84,8 +78,6 @@
 
 	/* This regulator controls the 3V3_S line, which powers sensors on-board. */
 	reg-3v3-sensor {
-		pinctrl-0 = <&pinmux_sensor>;
-		pinctrl-names = "default";
 		compatible = "regulator-fixed";
 		regulator-name = "reg-3v3-sensor";
 		enable-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
@@ -96,8 +88,6 @@
 
 	/* This regulator controls VDD_3V3_SPEKTRUM onboard supply */
 	reg-3v3-spektrum {
-		pinctrl-0 = <&pinmux_sensor>;
-		pinctrl-names = "default";
 		compatible = "regulator-fixed";
 		regulator-name = "reg-3v3-spektrum";
 		enable-gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
@@ -107,8 +97,6 @@
 
 	/* This regulator controls ETH_VDD_3V3 supply to power up the TJA1103 PHY */
 	reg-eth-power {
-		pinctrl-0 = <&pinmux_sensor>;
-		pinctrl-names = "default";
 		compatible = "regulator-fixed";
 		regulator-name = "reg-eth-power";
 		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;