Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel…

…/git/hskinnemoen/avr32-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  [AVR32] Initialize phy_mask for both macb devices
  [AVR32] Fix atomic_add_unless() and atomic_sub_unless()
  [AVR32] Correct misspelled CONFIG_BLK_DEV_INITRD variable.
  [AVR32] Fix build error in parse_tag_rdimg()
  [AVR32] Don't wire up macb0 unless SW6 is in default position
  [AVR32] Wire up SSC platform device 0 as TX on ATSTK1000 board
  [AVR32] Add Atmel SSC driver platform device to AT32AP architecture
  [AVR32] Remove optimization of unaligned word loads
  [AVR32] Make STK1000 mux settings configurable
  [AVR32] CPU frequency scaling for AT32AP
  [AVR32] Split SM device into PM, RTC, WDT and EIC
  [AVR32] faster avr32 unaligned access

arch/avr32/Kconfig

@@ -113,6 +113,10 @@ config BOARD_ATNGW100
 	bool "ATNGW100 Network Gateway"
 endchoice
 
+if BOARD_ATSTK1000
+source "arch/avr32/boards/atstk1000/Kconfig"
+endif
+
 choice
 	prompt "Boot loader type"
 	default LOADER_U_BOOT
@@ -185,6 +189,27 @@ config CMDLINE
 
 endmenu
 
+menu "Power managment options"
+
+menu "CPU Frequency scaling"
+
+source "drivers/cpufreq/Kconfig"
+
+config CPU_FREQ_AT32AP
+	bool "CPU frequency driver for AT32AP"
+	depends on CPU_FREQ && PLATFORM_AT32AP
+	default n
+	help
+	  This enables the CPU frequency driver for AT32AP processors.
+
+	  For details, take a look in <file:Documentation/cpu-freq>.
+
+	  If in doubt, say N.
+
+endmenu
+
+endmenu
+
 menu "Bus options"
 
 config PCI

arch/avr32/boards/atstk1000/Kconfig

@@ -0,0 +1,53 @@
+# STK1000 customization
+
+if BOARD_ATSTK1002
+
+config BOARD_ATSTK1002_CUSTOM
+	bool "Non-default STK-1002 jumper settings"
+	help
+	  You will normally leave the jumpers on the CPU card at their
+	  default settings.  If you need to use certain peripherals,
+	  you will need to change some of those jumpers.
+
+if BOARD_ATSTK1002_CUSTOM
+
+config BOARD_ATSTK1002_SW1_CUSTOM
+	bool "SW1: use SSC1 (not SPI0)"
+	help
+	  This also prevents using the external DAC as an audio interface,
+	  and means you can't initialize the on-board QVGA display.
+
+config BOARD_ATSTK1002_SW2_CUSTOM
+	bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)"
+	help
+	  If you change this you'll want an updated boot loader putting
+	  the console on UART-C not UART-A.
+
+config BOARD_ATSTK1002_SW3_CUSTOM
+	bool "SW3: use TIMER1 (not SSC0 and GCLK)"
+	help
+	  This also prevents using the external DAC as an audio interface.
+
+config BOARD_ATSTK1002_SW4_CUSTOM
+	bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)"
+	help
+	  To use the camera interface you'll need a custom card (on the
+	  PCI-format connector) connect a video sensor.
+
+config BOARD_ATSTK1002_SW5_CUSTOM
+	bool "SW5: use MACB1 (not LCDC)"
+
+config BOARD_ATSTK1002_SW6_CUSTOM
+	bool "SW6: more GPIOs (not MACB0)"
+
+endif	# custom
+
+config BOARD_ATSTK1002_SPI1
+	bool "Configure SPI1 controller"
+	depends on !BOARD_ATSTK1002_SW4_CUSTOM
+	help
+	  All the signals for the second SPI controller are available on
+	  GPIO lines and accessed through the J1 jumper block.  Say "y"
+	  here to configure that SPI controller.
+
+endif	# stk 1002

arch/avr32/boards/atstk1000/atstk1002.c

@@ -27,15 +27,27 @@
 
 #include "atstk1000.h"
 
-#define	SW2_DEFAULT		/* MMCI and UART_A available */
 
 struct eth_addr {
 	u8 addr[6];
 };
 
 static struct eth_addr __initdata hw_addr[2];
-static struct eth_platform_data __initdata eth_data[2];
+static struct eth_platform_data __initdata eth_data[2] = {
+	{
+		/*
+		 * The MDIO pullups on STK1000 are a bit too weak for
+		 * the autodetection to work properly, so we have to
+		 * mask out everything but the correct address.
+		 */
+		.phy_mask	= ~(1U << 16),
+	},
+	{
+		.phy_mask	= ~(1U << 17),
+	},
+};
 
+#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM
 static struct spi_board_info spi0_board_info[] __initdata = {
 	{
 		/* QVGA display */
@@ -45,6 +57,13 @@ static struct spi_board_info spi0_board_info[] __initdata = {
 		.mode		= SPI_MODE_3,
 	},
 };
+#endif
+
+#ifdef CONFIG_BOARD_ATSTK1002_SPI1
+static struct spi_board_info spi1_board_info[] __initdata = { {
+	/* patch in custom entries here */
+} };
+#endif
 
 /*
  * The next two functions should go away as the boot loader is
@@ -103,10 +122,10 @@ static void __init set_hw_addr(struct platform_device *pdev)
 
 void __init setup_board(void)
 {
-#ifdef	SW2_DEFAULT
-	at32_map_usart(1, 0);	/* USART 1/A: /dev/ttyS0, DB9 */
-#else
+#ifdef	CONFIG_BOARD_ATSTK1002_SW2_CUSTOM
 	at32_map_usart(0, 1);	/* USART 0/B: /dev/ttyS1, IRDA */
+#else
+	at32_map_usart(1, 0);	/* USART 1/A: /dev/ttyS0, DB9 */
 #endif
 	/* USART 2/unused: expansion connector */
 	at32_map_usart(3, 2);	/* USART 3/C: /dev/ttyS2, DB9 */
@@ -140,18 +159,31 @@ static int __init atstk1002_init(void)
 
 	at32_add_system_devices();
 
-#ifdef	SW2_DEFAULT
-	at32_add_device_usart(0);
-#else
+#ifdef	CONFIG_BOARD_ATSTK1002_SW2_CUSTOM
 	at32_add_device_usart(1);
+#else
+	at32_add_device_usart(0);
 #endif
 	at32_add_device_usart(2);
 
+#ifndef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM
 	set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
-
+#endif
+#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM
 	at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
+#endif
+#ifdef CONFIG_BOARD_ATSTK1002_SPI1
+	at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
+#endif
+#ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM
+	set_hw_addr(at32_add_device_eth(1, &eth_data[1]));
+#else
 	at32_add_device_lcdc(0, &atstk1000_lcdc_data,
 			     fbmem_start, fbmem_size);
+#endif
+#ifndef CONFIG_BOARD_ATSTK1002_SW3_CUSTOM
+	at32_add_device_ssc(0, ATMEL_SSC_TX);
+#endif
 
 	return 0;
 }

arch/avr32/kernel/setup.c

@@ -313,7 +313,7 @@ __tagtable(ATAG_MEM, parse_tag_mem);
 
 static int __init parse_tag_rdimg(struct tag *tag)
 {
-#ifdef CONFIG_INITRD
+#ifdef CONFIG_BLK_DEV_INITRD
 	struct tag_mem_range *mem = &tag->u.mem_range;
 	int ret;
 
@@ -323,7 +323,7 @@ static int __init parse_tag_rdimg(struct tag *tag)
 		return 0;
 	}
 
-	ret = add_reserved_region(mem->start, mem->start + mem->size - 1,
+	ret = add_reserved_region(mem->addr, mem->addr + mem->size - 1,
 				  "initrd");
 	if (ret) {
 		printk(KERN_WARNING

arch/avr32/mach-at32ap/Makefile

@@ -1,3 +1,4 @@
 obj-y				+= at32ap.o clock.o intc.o extint.o pio.o hsmc.o
 obj-$(CONFIG_CPU_AT32AP7000)	+= at32ap7000.o
 obj-$(CONFIG_CPU_AT32AP7000)	+= time-tc.o
+obj-$(CONFIG_CPU_FREQ_AT32AP)	+= cpufreq.o

arch/avr32/mach-at32ap/at32ap.c

@@ -11,41 +11,10 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 
-#include <asm/io.h>
-
 #include <asm/arch/init.h>
-#include <asm/arch/sm.h>
-
-struct at32_sm system_manager;
-
-static int __init at32_sm_init(void)
-{
-	struct resource *regs;
-	struct at32_sm *sm = &system_manager;
-	int ret = -ENXIO;
-
-	regs = platform_get_resource(&at32_sm_device, IORESOURCE_MEM, 0);
-	if (!regs)
-		goto fail;
-
-	spin_lock_init(&sm->lock);
-	sm->pdev = &at32_sm_device;
-
-	ret = -ENOMEM;
-	sm->regs = ioremap(regs->start, regs->end - regs->start + 1);
-	if (!sm->regs)
-		goto fail;
-
-	return 0;
-
-fail:
-	printk(KERN_ERR "Failed to initialize System Manager: %d\n", ret);
-	return ret;
-}
 
 void __init setup_platform(void)
 {
-	at32_sm_init();
 	at32_clock_init();
 	at32_portmux_init();
 }