mmc: sdhci-esdhc-imx: name esdhc specific definitions with ESDHC_ prefix

Rename esdhc local definitions with ESDHC_ rather than SDHCI_ prefix,
so that we can distinguish them from SDHCI core definitions from name.

A couple of bit fields are also changed use shift for consistency and
better readability.

Signed-off-by: Shawn Guo <[email protected]>
Tested-by: Dirk Behme <[email protected]>
Signed-off-by: Chris Ball <[email protected]>

drivers/mmc/host/sdhci-esdhc-imx.c

@@ -30,20 +30,20 @@
 #include "sdhci-pltfm.h"
 #include "sdhci-esdhc.h"
 
-#define	SDHCI_CTRL_D3CD			0x08
+#define	ESDHC_CTRL_D3CD			0x08
 /* VENDOR SPEC register */
-#define SDHCI_VENDOR_SPEC		0xC0
-#define  SDHCI_VENDOR_SPEC_SDIO_QUIRK	0x00000002
-#define SDHCI_WTMK_LVL			0x44
-#define SDHCI_MIX_CTRL			0x48
+#define ESDHC_VENDOR_SPEC		0xc0
+#define  ESDHC_VENDOR_SPEC_SDIO_QUIRK	(1 << 1)
+#define ESDHC_WTMK_LVL			0x44
+#define ESDHC_MIX_CTRL			0x48
 
 /*
  * There is an INT DMA ERR mis-match between eSDHC and STD SDHC SPEC:
  * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
  * but bit28 is used as the INT DMA ERR in fsl eSDHC design.
  * Define this macro DMA error INT for fsl eSDHC
  */
-#define SDHCI_INT_VENDOR_SPEC_DMA_ERR	0x10000000
+#define ESDHC_INT_VENDOR_SPEC_DMA_ERR	(1 << 28)
 
 /*
  * The CMDTYPE of the CMD register (offset 0xE) should be set to
@@ -165,8 +165,8 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
 	}
 
 	if (unlikely(reg == SDHCI_INT_STATUS)) {
-		if (val & SDHCI_INT_VENDOR_SPEC_DMA_ERR) {
-			val &= ~SDHCI_INT_VENDOR_SPEC_DMA_ERR;
+		if (val & ESDHC_INT_VENDOR_SPEC_DMA_ERR) {
+			val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR;
 			val |= SDHCI_INT_ADMA_ERROR;
 		}
 	}
@@ -192,9 +192,9 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
 			 * re-sample it by the following steps.
 			 */
 			data = readl(host->ioaddr + SDHCI_HOST_CONTROL);
-			data &= ~SDHCI_CTRL_D3CD;
+			data &= ~ESDHC_CTRL_D3CD;
 			writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
-			data |= SDHCI_CTRL_D3CD;
+			data |= ESDHC_CTRL_D3CD;
 			writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
 		}
 	}
@@ -203,15 +203,15 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
 				&& (reg == SDHCI_INT_STATUS)
 				&& (val & SDHCI_INT_DATA_END))) {
 			u32 v;
-			v = readl(host->ioaddr + SDHCI_VENDOR_SPEC);
-			v &= ~SDHCI_VENDOR_SPEC_SDIO_QUIRK;
-			writel(v, host->ioaddr + SDHCI_VENDOR_SPEC);
+			v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
+			v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK;
+			writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
 	}
 
 	if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
 		if (val & SDHCI_INT_ADMA_ERROR) {
 			val &= ~SDHCI_INT_ADMA_ERROR;
-			val |= SDHCI_INT_VENDOR_SPEC_DMA_ERR;
+			val |= ESDHC_INT_VENDOR_SPEC_DMA_ERR;
 		}
 	}
 
@@ -253,9 +253,9 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 				&& (host->cmd->data->blocks > 1)
 				&& (host->cmd->data->flags & MMC_DATA_READ)) {
 			u32 v;
-			v = readl(host->ioaddr + SDHCI_VENDOR_SPEC);
-			v |= SDHCI_VENDOR_SPEC_SDIO_QUIRK;
-			writel(v, host->ioaddr + SDHCI_VENDOR_SPEC);
+			v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
+			v |= ESDHC_VENDOR_SPEC_SDIO_QUIRK;
+			writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
 		}
 		imx_data->scratchpad = val;
 		return;
@@ -266,9 +266,9 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 			val |= SDHCI_CMD_ABORTCMD;
 
 		if (is_imx6q_usdhc(imx_data)) {
-			u32 m = readl(host->ioaddr + SDHCI_MIX_CTRL);
+			u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
 			m = imx_data->scratchpad | (m & 0xffff0000);
-			writel(m, host->ioaddr + SDHCI_MIX_CTRL);
+			writel(m, host->ioaddr + ESDHC_MIX_CTRL);
 			writel(val << 16,
 			       host->ioaddr + SDHCI_TRANSFER_MODE);
 		} else {
@@ -487,7 +487,7 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
 	 * to something insane.  Change it back here.
 	 */
 	if (is_imx6q_usdhc(imx_data))
-		writel(0x08100810, host->ioaddr + SDHCI_WTMK_LVL);
+		writel(0x08100810, host->ioaddr + ESDHC_WTMK_LVL);
 
 	boarddata = &imx_data->boarddata;
 	if (sdhci_esdhc_imx_probe_dt(pdev, boarddata) < 0) {