USB: move isp1301_omap to drivers/usb/otg

This moves the isp1301-omap driver from the drivers/i2c/chips
directory (which will be shrinking) into a new drivers/usb/otg
directory (which will grow, with more drivers and utilities).

Note that OTG infrastructure needs to be initialized before
either host or peripheral side USB support, and may be needed
before for pure host or pure peripheral configurations.

Signed-off-by: David Brownell <[email protected]>
Acked-by: Jean Delvare <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

drivers/Makefile

@@ -57,6 +57,7 @@ obj-$(CONFIG_ATA_OVER_ETH)	+= block/aoe/
 obj-$(CONFIG_PARIDE) 		+= block/paride/
 obj-$(CONFIG_TC)		+= tc/
 obj-$(CONFIG_UWB)		+= uwb/
+obj-$(CONFIG_USB_OTG_UTILS)	+= usb/otg/
 obj-$(CONFIG_USB)		+= usb/
 obj-$(CONFIG_USB_MUSB_HDRC)	+= usb/musb/
 obj-$(CONFIG_PCI)		+= usb/

drivers/i2c/chips/Kconfig

@@ -114,18 +114,6 @@ config SENSORS_PCF8591
 	  These devices are hard to detect and rarely found on mainstream
 	  hardware.  If unsure, say N.
 
-config ISP1301_OMAP
-	tristate "Philips ISP1301 with OMAP OTG"
-	depends on ARCH_OMAP_OTG
-	help
-	  If you say yes here you get support for the Philips ISP1301
-	  USB-On-The-Go transceiver working with the OMAP OTG controller.
-	  The ISP1301 is used in products including H2 and H3 development
-	  boards for Texas Instruments OMAP processors.
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called isp1301_omap.
-
 config SENSORS_MAX6875
 	tristate "Maxim MAX6875 Power supply supervisor"
 	depends on EXPERIMENTAL

drivers/i2c/chips/Makefile

@@ -18,7 +18,6 @@ obj-$(CONFIG_SENSORS_PCA9539)	+= pca9539.o
 obj-$(CONFIG_SENSORS_PCF8574)	+= pcf8574.o
 obj-$(CONFIG_PCF8575)		+= pcf8575.o
 obj-$(CONFIG_SENSORS_PCF8591)	+= pcf8591.o
-obj-$(CONFIG_ISP1301_OMAP)	+= isp1301_omap.o
 obj-$(CONFIG_SENSORS_TSL2550)	+= tsl2550.o
 obj-$(CONFIG_MCU_MPC8349EMITX)	+= mcu_mpc8349emitx.o
 

drivers/usb/Kconfig

@@ -150,4 +150,6 @@ source "drivers/usb/atm/Kconfig"
 
 source "drivers/usb/gadget/Kconfig"
 
+source "drivers/usb/otg/Kconfig"
+
 endif # USB_SUPPORT

drivers/usb/otg/Kconfig

@@ -0,0 +1,31 @@
+#
+# USB OTG infrastructure may be needed for peripheral-only, host-only,
+# or OTG-capable configurations when OTG transceivers or controllers
+# are used.
+#
+
+comment "OTG and related infrastructure"
+
+if USB || USB_GADGET
+
+config USB_OTG_UTILS
+	bool
+	help
+	  Select this to make sure the build includes objects from
+	  the OTG infrastructure directory.
+
+config ISP1301_OMAP
+	tristate "Philips ISP1301 with OMAP OTG"
+	depends on I2C && ARCH_OMAP_OTG
+	select USB_OTG_UTILS
+	help
+	  If you say yes here you get support for the Philips ISP1301
+	  USB-On-The-Go transceiver working with the OMAP OTG controller.
+	  The ISP1301 is a full speed USB  transceiver which is used in
+	  products including H2, H3, and H4 development boards for Texas
+	  Instruments OMAP processors.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called isp1301_omap.
+
+endif # USB || OTG

drivers/usb/otg/Makefile

@@ -0,0 +1,8 @@
+obj-$(CONFIG_ISP1301_OMAP)	+= isp1301_omap.o
+
+ifeq ($(CONFIG_USB_DEBUG),y)
+EXTRA_CFLAGS += -DDEBUG
+else ifeq ($(CONFIG_USB_GADGET_DEBUG),y)
+EXTRA_CFLAGS += -DDEBUG
+endif
+