ARC: [arcfpga] Get rid of legacy BVCI latency unit support

Signed-off-by: Vineet Gupta <[email protected]>

arch/arc/plat-arcfpga/Kconfig

@@ -48,36 +48,4 @@ config ARC_SERIAL_BAUD
 	help
 	  Baud rate for the ARC UART
 
-menuconfig ARC_HAS_BVCI_LAT_UNIT
-	bool "BVCI Bus Latency Unit"
-	depends on ARC_BOARD_ML509 || ARC_BOARD_ANGEL4
-	help
-	  IP to add artificial latency to BVCI Bus Based FPGA builds.
-	  The default latency (even worst case) for FPGA is non-realistic
-	  (~10 SDRAM, ~5 SSRAM).
-
-config BVCI_LAT_UNITS
-	hex "Latency Unit(s) Bitmap"
-	default "0x0"
-	depends on ARC_HAS_BVCI_LAT_UNIT
-	help
-	  There are multiple Latency Units corresponding to the many
-	  interfaces of the system bus arbiter (both CPU side as well as
-	  the peripheral side).
-	  To add latency to ALL memory transaction, choose Unit 0, otherwise
-	  for finer grainer - interface wise latency, specify a bitmap (1 bit
-	  per unit) of all units. e.g. 1,2,12 will be 0x1003
-
-	  Unit  0 - System Arb and Mem Controller
-	  Unit  1 - I$ and System Bus
-	  Unit  2 - D$ and System Bus
-	  ..
-	  Unit 12 - IDE Disk controller and System Bus
-
-config BVCI_LAT_CYCLES
-	int "Latency Value in cycles"
-	range 0 63
-	default "30"
-	depends on ARC_HAS_BVCI_LAT_UNIT
-
 endif

arch/arc/plat-arcfpga/platform.c

@@ -22,59 +22,6 @@
 #include <plat/smp.h>
 #include <plat/irq.h>
 
-/*-----------------------BVCI Latency Unit -----------------------------*/
-
-#ifdef CONFIG_ARC_HAS_BVCI_LAT_UNIT
-
-int lat_cycles = CONFIG_BVCI_LAT_CYCLES;
-
-/* BVCI Bus Profiler: Latency Unit */
-static void __init setup_bvci_lat_unit(void)
-{
-#define MAX_BVCI_UNITS 12
-
-	unsigned int i;
-	unsigned int *base = (unsigned int *)BVCI_LAT_UNIT_BASE;
-	const unsigned long units_req = CONFIG_BVCI_LAT_UNITS;
-	const unsigned int REG_UNIT = 21;
-	const unsigned int REG_VAL = 22;
-
-	/*
-	 * There are multiple Latency Units corresponding to the many
-	 * interfaces of the system bus arbiter (both CPU side as well as
-	 * the peripheral side).
-	 *
-	 * Unit  0 - System Arb and Mem Controller - adds latency to all
-	 *	    memory trasactions
-	 * Unit  1 - I$ and System Bus
-	 * Unit  2 - D$ and System Bus
-	 * ..
-	 * Unit 12 - IDE Disk controller and System Bus
-	 *
-	 * The programmers model requires writing to lat_unit reg first
-	 * and then the latency value (cycles) to lat_value reg
-	 */
-
-	if (CONFIG_BVCI_LAT_UNITS == 0) {
-		writel(0, base + REG_UNIT);
-		writel(lat_cycles, base + REG_VAL);
-		pr_info("BVCI Latency for all Memory Transactions %d cycles\n",
-			lat_cycles);
-	} else {
-		for_each_set_bit(i, &units_req, MAX_BVCI_UNITS) {
-			writel(i + 1, base + REG_UNIT); /* loop is 0 based */
-			writel(lat_cycles, base + REG_VAL);
-			pr_info("BVCI Latency for Unit[%d] = %d cycles\n",
-				(i + 1), lat_cycles);
-		}
-	}
-}
-#else
-static void __init setup_bvci_lat_unit(void)
-{
-}
-#endif
-
 /*----------------------- Platform Devices -----------------------------*/
 
 #if IS_ENABLED(CONFIG_SERIAL_ARC)
@@ -165,8 +112,6 @@ static void __init plat_fpga_early_init(void)
 {
 	pr_info("[plat-arcfpga]: registering early dev resources\n");
 
-	setup_bvci_lat_unit();
-
 	arc_fpga_serial_init();
 
 #ifdef CONFIG_ISS_SMP_EXTN