Merge tag 'asoc-v4.19' of https://git.kernel.org/pub/scm/linux/kernel…

…/git/broonie/sound into for-linus

ASoC: Updates for v4.19

A fairly big update, including quite a bit of core activity this time
around (which is good to see) along with a fairly large set of new
drivers.

 - A new snd_pcm_stop_xrun() helper which is now used in several
   drivers.
 - Support for providing name prefixes to generic component nodes.
 - Quite a few fixes for DPCM as it gains a bit wider use and more
   robust testing.
 - Generalization of the DIO2125 support to a simple amplifier driver.
 - Accessory detection support for the audio graph card.
 - DT support for PXA AC'97 devices.
 - Quirks for a number of new x86 systems.
 - Support for AM Logic Meson, Everest ES7154, Intel systems with
   RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707.

Documentation/device-mapper/writecache.txt

@@ -15,6 +15,8 @@ Constructor parameters:
    size)
 5. the number of optional parameters (the parameters with an argument
    count as two)
+	start_sector n		(default: 0)
+		offset from the start of cache device in 512-byte sectors
 	high_watermark n	(default: 50)
 		start writeback when the number of used blocks reach this
 		watermark

Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt

@@ -66,7 +66,7 @@ Required root node properties:
 	- "insignal,arndale-octa" - for Exynos5420-based Insignal Arndale
 				    Octa board.
 	- "insignal,origen"       - for Exynos4210-based Insignal Origen board.
-	- "insignal,origen4412    - for Exynos4412-based Insignal Origen board.
+	- "insignal,origen4412"   - for Exynos4412-based Insignal Origen board.
 
 
 Optional nodes:

Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt

@@ -36,7 +36,7 @@ Optional nodes:
 
  - port/ports: to describe a connection to an external encoder. The
    binding follows Documentation/devicetree/bindings/graph.txt and
-   suppors a single port with a single endpoint.
+   supports a single port with a single endpoint.
 
  - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and
    Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting

Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt

@@ -1,7 +1,7 @@
 Nintendo Wii (Hollywood) GPIO controller
 
 Required properties:
-- compatible: "nintendo,hollywood-gpio
+- compatible: "nintendo,hollywood-gpio"
 - reg: Physical base address and length of the controller's registers.
 - gpio-controller: Marks the device node as a GPIO controller.
 - #gpio-cells: Should be <2>. The first cell is the pin number and the

Documentation/devicetree/bindings/input/touchscreen/hideep.txt

@@ -32,7 +32,7 @@ i2c@00000000 {
 		reg = <0x6c>;
 		interrupt-parent = <&gpx1>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
-		vdd-supply = <&ldo15_reg>";
+		vdd-supply = <&ldo15_reg>;
 		vid-supply = <&ldo18_reg>;
 		reset-gpios = <&gpx1 5 0>;
 		touchscreen-size-x = <1080>;

Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt

@@ -15,7 +15,7 @@ Required properties:
   include "nvidia,tegra30-ictlr".	
 - reg : Specifies base physical address and size of the registers.
   Each controller must be described separately (Tegra20 has 4 of them,
-  whereas Tegra30 and later have 5"  
+  whereas Tegra30 and later have 5).
 - interrupt-controller : Identifies the node as an interrupt controller.
 - #interrupt-cells : Specifies the number of cells needed to encode an
   interrupt source. The value must be 3.

Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt

@@ -12,7 +12,7 @@ Required properties:
   specifier, shall be 2
 - interrupts: interrupts references to primary interrupt controller
   (only needed for exti controller with multiple exti under
-  same parent interrupt: st,stm32-exti and st,stm32h7-exti")
+  same parent interrupt: st,stm32-exti and st,stm32h7-exti)
 
 Example:
 

Documentation/devicetree/bindings/mips/brcm/soc.txt

@@ -152,7 +152,7 @@ Required properties:
 - compatible	: should contain one of:
 		  "brcm,bcm7425-timers"
 		  "brcm,bcm7429-timers"
-		  "brcm,bcm7435-timers and
+		  "brcm,bcm7435-timers" and
 		  "brcm,brcmstb-timers"
 - reg		: the timers register range
 - interrupts	: the interrupt line for this timer block

Documentation/devicetree/bindings/net/fsl-fman.txt

@@ -238,7 +238,7 @@ PROPERTIES
 		Must include one of the following:
 		- "fsl,fman-dtsec" for dTSEC MAC
 		- "fsl,fman-xgec" for XGEC MAC
-		- "fsl,fman-memac for mEMAC MAC
+		- "fsl,fman-memac" for mEMAC MAC
 
 - cell-index
 		Usage: required

Documentation/devicetree/bindings/power/power_domain.txt

@@ -133,7 +133,7 @@ located inside a PM domain with index 0 of a power controller represented by a
 node with the label "power".
 In the second example the consumer device are partitioned across two PM domains,
 the first with index 0 and the second with index 1, of a power controller that
-is represented by a node with the label "power.
+is represented by a node with the label "power".
 
 Optional properties:
 - required-opps: This contains phandle to an OPP node in another device's OPP

Documentation/devicetree/bindings/regulator/tps65090.txt

@@ -16,7 +16,7 @@ Required properties:
 Optional properties:
 - ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
   If DCDCs are externally controlled then this property should be there.
-- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
+- dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
   If DCDCs are externally controlled and if it is from GPIO then GPIO
   number should be provided. If it is externally controlled and no GPIO
   entry then driver will just configure this rails as external control

Documentation/devicetree/bindings/reset/st,sti-softreset.txt

@@ -15,7 +15,7 @@ Please refer to reset.txt in this directory for common reset
 controller binding usage.
 
 Required properties:
-- compatible: Should be st,stih407-softreset";
+- compatible: Should be "st,stih407-softreset";
 - #reset-cells: 1, see below
 
 example:

Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt

@@ -39,7 +39,7 @@ Required properties:
 
 Optional property:
 - clock-frequency:	Desired I2C bus clock frequency in Hz.
-			When missing default to 400000Hz.
+			When missing default to 100000Hz.
 
 Child nodes should conform to I2C bus binding as described in i2c.txt.
 

Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt

@@ -0,0 +1,23 @@
+* Amlogic Audio FIFO controllers
+
+Required properties:
+- compatible: 'amlogic,axg-toddr' or
+	      'amlogic,axg-frddr'
+- reg: physical base address of the controller and length of memory
+       mapped region.
+- interrupts: interrupt specifier for the fifo.
+- clocks: phandle to the fifo peripheral clock provided by the audio
+	  clock controller.
+- resets: phandle to memory ARB line provided by the arb reset controller.
+- #sound-dai-cells: must be 0.
+
+Example of FRDDR A on the A113 SoC:
+
+frddr_a: audio-controller@1c0 {
+	compatible = "amlogic,axg-frddr";
+	reg = <0x0 0x1c0 0x0 0x1c>;
+	#sound-dai-cells = <0>;
+	interrupts = <GIC_SPI 88 IRQ_TYPE_EDGE_RISING>;
+	clocks = <&clkc_audio AUD_CLKID_FRDDR_A>;
+	resets = <&arb AXG_ARB_FRDDR_A>;
+};

Documentation/devicetree/bindings/sound/amlogic,axg-sound-card.txt

@@ -0,0 +1,124 @@
+Amlogic AXG sound card:
+
+Required properties:
+
+- compatible: "amlogic,axg-sound-card"
+- model : User specified audio sound card name, one string
+
+Optional properties:
+
+- audio-aux-devs : List of phandles pointing to auxiliary devices
+- audio-widgets : Please refer to widgets.txt.
+- audio-routing : A list of the connections between audio components.
+
+Subnodes:
+
+- dai-link: Container for dai-link level properties and the CODEC
+	    sub-nodes. There should be at least one (and probably more)
+	    subnode of this type.
+
+Required dai-link properties:
+
+- sound-dai: phandle and port of the CPU DAI.
+
+Required TDM Backend dai-link properties:
+- dai-format : CPU/CODEC common audio format
+
+Optional TDM Backend dai-link properties:
+- dai-tdm-slot-rx-mask-{0,1,2,3}: Receive direction slot masks
+- dai-tdm-slot-tx-mask-{0,1,2,3}: Transmit direction slot masks
+				  When omitted, mask is assumed to have to no
+				  slots. A valid must have at one slot, so at
+				  least one these mask should be provided with
+				  an enabled slot.
+- dai-tdm-slot-num : Please refer to tdm-slot.txt.
+		     If omitted, slot number is set to accommodate the largest
+		     mask provided.
+- dai-tdm-slot-width : Please refer to tdm-slot.txt. default to 32 if omitted.
+- mclk-fs : Multiplication factor between stream rate and mclk
+
+Backend dai-link subnodes:
+
+- codec: dai-link representing backend links should have at least one subnode.
+	 One subnode for each codec of the dai-link.
+	 dai-link representing frontend links have no codec, therefore have no
+	 subnodes
+
+Required codec subnodes properties:
+
+- sound-dai: phandle and port of the CODEC DAI.
+
+Optional codec subnodes properties:
+
+- dai-tdm-slot-tx-mask : Please refer to tdm-slot.txt.
+- dai-tdm-slot-rx-mask : Please refer to tdm-slot.txt.
+
+Example:
+
+sound {
+	compatible = "amlogic,axg-sound-card";
+	model = "AXG-S420";
+	audio-aux-devs = <&tdmin_a>, <&tdmout_c>;
+	audio-widgets = "Line", "Lineout",
+			"Line", "Linein",
+			"Speaker", "Speaker1 Left",
+			"Speaker", "Speaker1 Right";
+			"Speaker", "Speaker2 Left",
+			"Speaker", "Speaker2 Right";
+	audio-routing = "TDMOUT_C IN 0", "FRDDR_A OUT 2",
+			"SPDIFOUT IN 0", "FRDDR_A OUT 3",
+			"TDM_C Playback", "TDMOUT_C OUT",
+			"TDMIN_A IN 2", "TDM_C Capture",
+			"TDMIN_A IN 5", "TDM_C Loopback",
+			"TODDR_A IN 0", "TDMIN_A OUT",
+			"Lineout", "Lineout AOUTL",
+			"Lineout", "Lineout AOUTR",
+			"Speaker1 Left", "SPK1 OUT_A",
+			"Speaker2 Left", "SPK2 OUT_A",
+			"Speaker1 Right", "SPK1 OUT_B",
+			"Speaker2 Right", "SPK2 OUT_B",
+			"Linein AINL", "Linein",
+			"Linein AINR", "Linein";
+
+	dai-link@0 {
+		sound-dai = <&frddr_a>;
+	};
+
+	dai-link@1 {
+		sound-dai = <&toddr_a>;
+	};
+
+	dai-link@2 {
+		sound-dai = <&tdmif_c>;
+		dai-format = "i2s";
+		dai-tdm-slot-tx-mask-2 = <1 1>;
+		dai-tdm-slot-tx-mask-3 = <1 1>;
+		dai-tdm-slot-rx-mask-1 = <1 1>;
+		mclk-fs = <256>;
+
+		codec@0 {
+			sound-dai = <&lineout>;
+		};
+
+		codec@1 {
+			sound-dai = <&speaker_amp1>;
+		};
+
+		codec@2 {
+			sound-dai = <&speaker_amp2>;
+		};
+
+		codec@3 {
+			sound-dai = <&linein>;
+		};
+
+	};
+
+	dai-link@3 {
+		sound-dai = <&spdifout>;
+
+		codec {
+			sound-dai = <&spdif_dit>;
+		};
+	};
+};

Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt

@@ -0,0 +1,20 @@
+* Amlogic Audio SPDIF Output
+
+Required properties:
+- compatible: 'amlogic,axg-spdifout'
+- clocks: list of clock phandle, one for each entry clock-names.
+- clock-names: should contain the following:
+  * "pclk" : peripheral clock.
+  * "mclk" : master clock
+- #sound-dai-cells: must be 0.
+
+Example on the A113 SoC:
+
+spdifout: audio-controller@480 {
+	compatible = "amlogic,axg-spdifout";
+	reg = <0x0 0x480 0x0 0x50>;
+	#sound-dai-cells = <0>;
+	clocks = <&clkc_audio AUD_CLKID_SPDIFOUT>,
+		 <&clkc_audio AUD_CLKID_SPDIFOUT_CLK>;
+	clock-names = "pclk", "mclk";
+};

Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt

@@ -0,0 +1,28 @@
+* Amlogic Audio TDM formatters
+
+Required properties:
+- compatible: 'amlogic,axg-tdmin' or
+	      'amlogic,axg-tdmout'
+- reg: physical base address of the controller and length of memory
+       mapped region.
+- clocks: list of clock phandle, one for each entry clock-names.
+- clock-names: should contain the following:
+  * "pclk"     : peripheral clock.
+  * "sclk"     : bit clock.
+  * "sclk_sel" : bit clock input multiplexer.
+  * "lrclk"    : sample clock
+  * "lrclk_sel": sample clock input multiplexer
+
+Example of TDMOUT_A on the A113 SoC:
+
+tdmout_a: audio-controller@500 {
+	compatible = "amlogic,axg-tdmout";
+	reg = <0x0 0x500 0x0 0x40>;
+	clocks = <&clkc_audio AUD_CLKID_TDMOUT_A>,
+		 <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK>,
+		 <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK_SEL>,
+		 <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>,
+		 <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>;
+	clock-names = "pclk", "sclk", "sclk_sel",
+		      "lrclk", "lrclk_sel";
+};

Documentation/devicetree/bindings/sound/amlogic,axg-tdm-iface.txt

@@ -0,0 +1,22 @@
+* Amlogic Audio TDM Interfaces
+
+Required properties:
+- compatible: 'amlogic,axg-tdm-iface'
+- clocks: list of clock phandle, one for each entry clock-names.
+- clock-names: should contain the following:
+  * "sclk" : bit clock.
+  * "lrclk": sample clock
+  * "mclk" : master clock
+	     -> optional if the interface is in clock slave mode.
+- #sound-dai-cells: must be 0.
+
+Example of TDM_A on the A113 SoC:
+
+tdmif_a: audio-controller@0 {
+	compatible = "amlogic,axg-tdm-iface";
+	#sound-dai-cells = <0>;
+	clocks = <&clkc_audio AUD_CLKID_MST_A_MCLK>,
+		 <&clkc_audio AUD_CLKID_MST_A_SCLK>,
+		 <&clkc_audio AUD_CLKID_MST_A_LRCLK>;
+	clock-names = "mclk", "sclk", "lrclk";
+};

Documentation/devicetree/bindings/sound/atmel-i2s.txt

@@ -15,17 +15,16 @@ Required properties:
 - clock-names:    Should be one of each entry matching the clocks phandles list:
                   - "pclk" (peripheral clock) Required.
                   - "gclk" (generated clock) Optional (1).
-                  - "aclk" (Audio PLL clock) Optional (1).
                   - "muxclk" (I2S mux clock) Optional (1).
 
 Optional properties:
 - pinctrl-0:      Should specify pin control groups used for this controller.
 - princtrl-names: Should contain only one value - "default".
 
 
-(1) : Only the peripheral clock is required. The generated clock, the Audio
-      PLL clock adn the I2S mux clock are optional and should only be set
-      together, when Master Mode is required.
+(1) : Only the peripheral clock is required. The generated clock and the I2S
+      mux clock are optional and should only be set together, when Master Mode
+      is required.
 
 Example:
 
@@ -40,8 +39,8 @@ Example:
 			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
 			 AT91_XDMAC_DT_PERID(32))>;
 		dma-names = "tx", "rx";
-		clocks = <&i2s0_clk>, <&i2s0_gclk>, <&audio_pll_pmc>, <&i2s0muxck>;
-		clock-names = "pclk", "gclk", "aclk", "muxclk";
+		clocks = <&i2s0_clk>, <&i2s0_gclk>, <&i2s0muxck>;
+		clock-names = "pclk", "gclk", "muxclk";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2s0_default>;
 	};

Documentation/devicetree/bindings/sound/audio-graph-card.txt

@@ -18,6 +18,8 @@ Below are same as Simple-Card.
 - bitclock-inversion
 - frame-inversion
 - mclk-fs
+- hp-det-gpio
+- mic-det-gpio
 - dai-tdm-slot-num
 - dai-tdm-slot-width
 - clocks / system-clock-frequency