DT: aat1290: Document handling external strobe sources

This patch adds documentation for a pinctrl-names property.
The property, when present, is used for switching the source
of the strobe signal for the device.

Signed-off-by: Jacek Anaszewski <[email protected]>
Acked-by: Kyungmin Park <[email protected]>
Cc: Bryan Wu <[email protected]>
Cc: Richard Purdie <[email protected]>
Cc: [email protected]
Acked-by: Sakari Ailus <[email protected]>
Signed-off-by: Bryan Wu <[email protected]>

Documentation/devicetree/bindings/leds/leds-aat1290.txt

@@ -2,14 +2,23 @@
 
 The device is controlled through two pins: FL_EN and EN_SET. The pins when,
 asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
-respectively.
+respectively. In order to add a capability of selecting the strobe signal source
+(e.g. CPU or camera sensor) there is an additional switch required, independent
+of the flash chip. The switch is controlled with pin control.
 
 Required properties:
 
 - compatible : Must be "skyworks,aat1290".
 - flen-gpios : Must be device tree identifier of the flash device FL_EN pin.
 - enset-gpios : Must be device tree identifier of the flash device EN_SET pin.
 
+Optional properties:
+- pinctrl-names : Must contain entries: "default", "host", "isp". Entries
+		"default" and "host" must refer to the same pin configuration
+		node, which sets the host as a strobe signal provider. Entry
+		"isp" must refer to the pin configuration node, which sets the
+		ISP as a strobe signal provider.
+
 A discrete LED element connected to the device must be represented by a child
 node - see Documentation/devicetree/bindings/leds/common.txt.
 
@@ -25,17 +34,40 @@ Required properties of the LED child node:
 Optional properties of the LED child node:
 - label : see Documentation/devicetree/bindings/leds/common.txt
 
-Example (by Ct = 220nF, Rset = 160kohm):
+Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with
+a switch that allows for routing strobe signal either from the host or from
+the camera sensor):
+
+#include "exynos4412.dtsi"
 
 aat1290 {
 	compatible = "skyworks,aat1290";
 	flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
 	enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
 
+	pinctrl-names = "default", "host", "isp";
+	pinctrl-0 = <&camera_flash_host>;
+	pinctrl-1 = <&camera_flash_host>;
+	pinctrl-2 = <&camera_flash_isp>;
+
 	camera_flash: flash-led {
 		label = "aat1290-flash";
 		led-max-microamp = <520833>;
 		flash-max-microamp = <1012500>;
 		flash-timeout-us = <1940000>;
 	};
 };
+
+&pinctrl_0 {
+	camera_flash_host: camera-flash-host {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <0>;
+	};
+
+	camera_flash_isp: camera-flash-isp {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <1>;
+	};
+};