Merge pull request MarlinFirmware#482 from codexmas/Marlin_v1

servosupport

Marlin/Configuration.h

@@ -2,7 +2,7 @@
 #define CONFIGURATION_H
 
 // This configurtion file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h 
+// Advanced settings can be found in Configuration_adv.h
 // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //User specified version info of this build to display in [Pronterface, etc] terminal window during startup.
@@ -78,7 +78,7 @@
 // 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
 // 10 is 100k RS thermistor 198-961 (4.7k pullup)
 //
-//    1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k 
+//    1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
 //                          (but gives greater accuracy and more stable PID)
 // 51 is 100k thermistor - EPCOS (1k pullup)
 // 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
@@ -95,7 +95,7 @@
 #define TEMP_WINDOW     1       // (degC) Window around target to start the recidency timer x degC early.
 
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
-// to check that the wiring to the thermistor is not broken. 
+// to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
 #define HEATER_0_MINTEMP 5
 #define HEATER_1_MINTEMP 5
@@ -121,7 +121,7 @@
 #define BANG_MAX 256 // limits current to nozzle while in bang-bang mode; 256=full current
 #define PID_MAX 256 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 256=full current
 #ifdef PIDTEMP
-  //#define PID_DEBUG // Sends debug data to the serial port. 
+  //#define PID_DEBUG // Sends debug data to the serial port.
   //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
   #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
                                   // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
@@ -132,15 +132,15 @@
 // If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it
 // Ultimaker
     #define  DEFAULT_Kp 22.2
-    #define  DEFAULT_Ki 1.08  
-    #define  DEFAULT_Kd 114  
+    #define  DEFAULT_Ki 1.08
+    #define  DEFAULT_Kd 114
 
 // Makergear
 //    #define  DEFAULT_Kp 7.0
-//    #define  DEFAULT_Ki 0.1  
-//    #define  DEFAULT_Kd 12  
+//    #define  DEFAULT_Ki 0.1
+//    #define  DEFAULT_Kd 12
 
-// Mendel Parts V9 on 12V    
+// Mendel Parts V9 on 12V
 //    #define  DEFAULT_Kp 63.0
 //    #define  DEFAULT_Ki 2.25
 //    #define  DEFAULT_Kd 440
@@ -149,11 +149,11 @@
 // Bed Temperature Control
 // Select PID or bang-bang with PIDTEMPBED.  If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
 //
-// uncomment this to enable PID on the bed.   It uses the same ferquency PWM as the extruder. 
+// uncomment this to enable PID on the bed.   It uses the same ferquency PWM as the extruder.
 // If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
 // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. 
-// If your configuration is significantly different than this and you don't understand the issues involved, you proabaly 
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you proabaly
 // shouldn't use bed PID until someone else verifies your hardware works.
 // If this is enabled, find your own PID constants below.
 //#define PIDTEMPBED
@@ -223,9 +223,9 @@
 #endif
 
 // The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
-const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 
-const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 
-const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 
+const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
+const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
+const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
 //#define DISABLE_MAX_ENDSTOPS
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@@ -280,13 +280,13 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
 #define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0}  // set the homing speeds (mm/min)
 
-// default settings 
+// default settings
 
 #define DEFAULT_AXIS_STEPS_PER_UNIT   {78.7402,78.7402,200.0*8/3,760*1.1}  // default steps per unit for ultimaker
 #define DEFAULT_MAX_FEEDRATE          {500, 500, 5, 25}    // (mm/sec)
 #define DEFAULT_MAX_ACCELERATION      {9000,9000,100,10000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
 
-#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E max acceleration in mm/s^2 for printing moves 
+#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E max acceleration in mm/s^2 for printing moves
 #define DEFAULT_RETRACT_ACCELERATION  3000   // X, Y, Z and E max acceleration in mm/s^2 for r retracts
 
 // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
@@ -307,7 +307,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 // EEPROM
 // the microcontroller can store settings in the EEPROM, e.g. max velocity...
 // M500 - stores paramters in EEPROM
-// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).  
+// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
 // M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
 //define this to enable eeprom support
 //#define EEPROM_SETTINGS
@@ -353,15 +353,15 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 #if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
  #define ULTIPANEL
  #define NEWPANEL
-#endif 
+#endif
 
 #if defined(REPRAPWORLD_KEYPAD)
   #define NEWPANEL
   #define ULTIPANEL
 #endif
 
 // Preheat Constants
-#define PLA_PREHEAT_HOTEND_TEMP 180 
+#define PLA_PREHEAT_HOTEND_TEMP 180
 #define PLA_PREHEAT_HPB_TEMP 70
 #define PLA_PREHEAT_FAN_SPEED 255		// Insert Value between 0 and 255
 
@@ -381,15 +381,15 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 		#define LCD_WIDTH 20
 		#define LCD_HEIGHT 4
 	#endif
-#else //no panel but just lcd 
+#else //no panel but just lcd
   #ifdef ULTRA_LCD
 	#ifdef DOGLCD	// Change number of lines to match the 128x64 graphics display
 		#define LCD_WIDTH 20
 		#define LCD_HEIGHT 5
 	#else
 		#define LCD_WIDTH 16
 		#define LCD_HEIGHT 2
-	#endif    
+	#endif
   #endif
 #endif
 
@@ -406,6 +406,23 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 // Support for the BariCUDA Paste Extruder.
 //#define BARICUDA
 
+/*********************************************************************\
+*
+* R/C SERVO support
+*
+* Sponsored by TrinityLabs, Reworked by codexmas
+*
+**********************************************************************/
+
+// Number of servos
+//
+// If you select a configuration below, this will receive a default value and does not need to be set manually
+// set it manually if you have more servos than extruders and wish to manually control some
+// leaving it undefined or defining as 0 will disable the servo subsystem
+// If unsure, leave commented / disabled
+//
+// #define NUM_SERVOS 3
+
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/Makefile

@@ -1,12 +1,12 @@
 # Sprinter Arduino Project Makefile
-# 
+#
 # Makefile Based on:
 # Arduino 0011 Makefile
 # Arduino adaptation by mellis, eighthave, oli.keller
 # Marlin adaption by Daid
 #
 # This has been tested with Arduino 0022.
-# 
+#
 # This makefile allows you to build sketches from the command line
 # without the Arduino environment (or Java).
 #
@@ -21,7 +21,7 @@
 #     (e.g. UPLOAD_PORT = /dev/tty.USB0).  If the exact name of this file
 #     changes, you can use * as a wildcard (e.g. UPLOAD_PORT = /dev/tty.usb*).
 #
-#  3. Set the line containing "MCU" to match your board's processor. 
+#  3. Set the line containing "MCU" to match your board's processor.
 #     Older one's are atmega8 based, newer ones like Arduino Mini, Bluetooth
 #     or Diecimila have the atmega168.  If you're using a LilyPad Arduino,
 #     change F_CPU to 8000000. If you are using Gen7 electronics, you
@@ -44,7 +44,7 @@ ARDUINO_INSTALL_DIR  ?= ../../arduino-0022
 ARDUINO_VERSION      ?= 22
 
 # You can optionally set a path to the avr-gcc tools. Requires a trailing slash. (ex: /usr/local/avr-gcc/bin)
-AVR_TOOLS_PATH ?= 
+AVR_TOOLS_PATH ?=
 
 #Programmer configuration
 UPLOAD_RATE        ?= 115200
@@ -213,7 +213,7 @@ CXXSRC = WMath.cpp WString.cpp Print.cpp Marlin_main.cpp	\
 	SdFile.cpp SdVolume.cpp motion_control.cpp planner.cpp		\
 	stepper.cpp temperature.cpp cardreader.cpp ConfigurationStore.cpp \
 	watchdog.cpp
-CXXSRC += LiquidCrystal.cpp ultralcd.cpp SPI.cpp
+CXXSRC += LiquidCrystal.cpp ultralcd.cpp SPI.cpp Servo.cpp
 
 #Check for Arduino 1.0.0 or higher and use the correct sourcefiles for that version
 ifeq ($(shell [ $(ARDUINO_VERSION) -ge 100 ] && echo true), true)
@@ -317,19 +317,19 @@ endif
 # Default target.
 all: sizeafter
 
-build: $(BUILD_DIR) elf hex 
+build: $(BUILD_DIR) elf hex
 
 # Creates the object directory
-$(BUILD_DIR): 
+$(BUILD_DIR):
 	$P mkdir -p $(BUILD_DIR)
 
 elf: $(BUILD_DIR)/$(TARGET).elf
 hex: $(BUILD_DIR)/$(TARGET).hex
 eep: $(BUILD_DIR)/$(TARGET).eep
-lss: $(BUILD_DIR)/$(TARGET).lss 
+lss: $(BUILD_DIR)/$(TARGET).lss
 sym: $(BUILD_DIR)/$(TARGET).sym
 
-# Program the device.  
+# Program the device.
 # Do not try to reset an arduino if it's not one
 upload: $(BUILD_DIR)/$(TARGET).hex
 ifeq (${AVRDUDE_PROGRAMMER}, arduino)
@@ -356,7 +356,7 @@ COFFCONVERT=$(OBJCOPY) --debugging \
 	--change-section-address .data-0x800000 \
 	--change-section-address .bss-0x800000 \
 	--change-section-address .noinit-0x800000 \
-	--change-section-address .eeprom-0x810000 
+	--change-section-address .eeprom-0x810000
 
 
 coff: $(BUILD_DIR)/$(TARGET).elf