Merge tag 'omap-for-v5.6/droid4-lcd-fix-signed' of git://git.kernel.o…

…rg/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes

Fix LCD backlight issue for droid4

There was a bit of an integration glitch with the LED backlight series.
The LED related parts got merged into v5.6-rc1, but the actual backlight
driver got left out.

This caused an issue on at least droid4 where the LCD backlight can not
yet be enabled automatically. And the LCD backlight can no longer be
enabled manually either via sysfs.

The integration glitch happened because some pending comments from me.
There was some confusion on which device tree property we should use for
the default brightness property.

After discussing how to fix this on the mailing lists, we came to the
conclusion that it's best to fix this issue properly by adding the
missing driver.

The other solutions would mean backpedaling and try to come up with some
temporary solution that really does not solve the issue for users. The
patch for led_bl.c has been around for quite a while and tested by many
users and was assumed to be merged as part of the LED backlight series.

For the brightness property to use, we ended up using the more common
"default-brightness-level" rather than "default-brightness" used by
some backlight drivers.

* tag 'omap-for-v5.6/droid4-lcd-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: droid4: Configure LED backlight for lm3532
  backlight: add led-backlight driver

Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Olof Johansson <[email protected]>

arch/arm/boot/dts/motorola-mapphone-common.dtsi

@@ -182,6 +182,14 @@
 		pwm-names = "enable", "direction";
 		direction-duty-cycle-ns = <10000000>;
 	};
+
+	backlight: backlight {
+		compatible = "led-backlight";
+
+		leds = <&backlight_led>;
+		brightness-levels = <31 63 95 127 159 191 223 255>;
+		default-brightness-level = <6>;
+	};
 };
 
 &dss {
@@ -205,6 +213,8 @@
 		vddi-supply = <&lcd_regulator>;
 		reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;	/* gpio101 */
 
+		backlight = <&backlight>;
+
 		width-mm = <50>;
 		height-mm = <89>;
 
@@ -393,12 +403,11 @@
 		ramp-up-us = <1024>;
 		ramp-down-us = <8193>;
 
-		led@0 {
+		backlight_led: led@0 {
 			reg = <0>;
 			led-sources = <2>;
 			ti,led-mode = <0>;
 			label = ":backlight";
-			linux,default-trigger = "backlight";
 		};
 
 		led@1 {

arch/arm/configs/omap2plus_defconfig

@@ -375,6 +375,7 @@ CONFIG_BACKLIGHT_GENERIC=m
 CONFIG_BACKLIGHT_PWM=m
 CONFIG_BACKLIGHT_PANDORA=m
 CONFIG_BACKLIGHT_GPIO=m
+CONFIG_BACKLIGHT_LED=m
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
 CONFIG_LOGO=y

drivers/video/backlight/Kconfig

@@ -456,6 +456,13 @@ config BACKLIGHT_RAVE_SP
 	help
 	  Support for backlight control on RAVE SP device.
 
+config BACKLIGHT_LED
+	tristate "Generic LED based Backlight Driver"
+	depends on LEDS_CLASS && OF
+	help
+	  If you have a LCD backlight adjustable by LED class driver, say Y
+	  to enable this driver.
+
 endif # BACKLIGHT_CLASS_DEVICE
 
 endmenu

drivers/video/backlight/Makefile

@@ -57,3 +57,4 @@ obj-$(CONFIG_BACKLIGHT_TPS65217)	+= tps65217_bl.o
 obj-$(CONFIG_BACKLIGHT_WM831X)		+= wm831x_bl.o
 obj-$(CONFIG_BACKLIGHT_ARCXCNN) 	+= arcxcnn_bl.o
 obj-$(CONFIG_BACKLIGHT_RAVE_SP)		+= rave-sp-backlight.o
+obj-$(CONFIG_BACKLIGHT_LED)		+= led_bl.o

drivers/video/backlight/led_bl.c

@@ -0,0 +1,260 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2015-2019 Texas Instruments Incorporated -  http://www.ti.com/
+ * Author: Tomi Valkeinen <[email protected]>
+ *
+ * Based on pwm_bl.c
+ */
+
+#include <linux/backlight.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+struct led_bl_data {
+	struct device		*dev;
+	struct backlight_device	*bl_dev;
+	struct led_classdev	**leds;
+	bool			enabled;
+	int			nb_leds;
+	unsigned int		*levels;
+	unsigned int		default_brightness;
+	unsigned int		max_brightness;
+};
+
+static void led_bl_set_brightness(struct led_bl_data *priv, int level)
+{
+	int i;
+	int bkl_brightness;
+
+	if (priv->levels)
+		bkl_brightness = priv->levels[level];
+	else
+		bkl_brightness = level;
+
+	for (i = 0; i < priv->nb_leds; i++)
+		led_set_brightness(priv->leds[i], bkl_brightness);
+
+	priv->enabled = true;
+}
+
+static void led_bl_power_off(struct led_bl_data *priv)
+{
+	int i;
+
+	if (!priv->enabled)
+		return;
+
+	for (i = 0; i < priv->nb_leds; i++)
+		led_set_brightness(priv->leds[i], LED_OFF);
+
+	priv->enabled = false;
+}
+
+static int led_bl_update_status(struct backlight_device *bl)
+{
+	struct led_bl_data *priv = bl_get_data(bl);
+	int brightness = bl->props.brightness;
+
+	if (bl->props.power != FB_BLANK_UNBLANK ||
+	    bl->props.fb_blank != FB_BLANK_UNBLANK ||
+	    bl->props.state & BL_CORE_FBBLANK)
+		brightness = 0;
+
+	if (brightness > 0)
+		led_bl_set_brightness(priv, brightness);
+	else
+		led_bl_power_off(priv);
+
+	return 0;
+}
+
+static const struct backlight_ops led_bl_ops = {
+	.update_status	= led_bl_update_status,
+};
+
+static int led_bl_get_leds(struct device *dev,
+			   struct led_bl_data *priv)
+{
+	int i, nb_leds, ret;
+	struct device_node *node = dev->of_node;
+	struct led_classdev **leds;
+	unsigned int max_brightness;
+	unsigned int default_brightness;
+
+	ret = of_count_phandle_with_args(node, "leds", NULL);
+	if (ret < 0) {
+		dev_err(dev, "Unable to get led count\n");
+		return -EINVAL;
+	}
+
+	nb_leds = ret;
+	if (nb_leds < 1) {
+		dev_err(dev, "At least one LED must be specified!\n");
+		return -EINVAL;
+	}
+
+	leds = devm_kzalloc(dev, sizeof(struct led_classdev *) * nb_leds,
+			    GFP_KERNEL);
+	if (!leds)
+		return -ENOMEM;
+
+	for (i = 0; i < nb_leds; i++) {
+		leds[i] = devm_of_led_get(dev, i);
+		if (IS_ERR(leds[i]))
+			return PTR_ERR(leds[i]);
+	}
+
+	/* check that the LEDs all have the same brightness range */
+	max_brightness = leds[0]->max_brightness;
+	for (i = 1; i < nb_leds; i++) {
+		if (max_brightness != leds[i]->max_brightness) {
+			dev_err(dev, "LEDs must have identical ranges\n");
+			return -EINVAL;
+		}
+	}
+
+	/* get the default brightness from the first LED from the list */
+	default_brightness = leds[0]->brightness;
+
+	priv->nb_leds = nb_leds;
+	priv->leds = leds;
+	priv->max_brightness = max_brightness;
+	priv->default_brightness = default_brightness;
+
+	return 0;
+}
+
+static int led_bl_parse_levels(struct device *dev,
+			   struct led_bl_data *priv)
+{
+	struct device_node *node = dev->of_node;
+	int num_levels;
+	u32 value;
+	int ret;
+
+	if (!node)
+		return -ENODEV;
+
+	num_levels = of_property_count_u32_elems(node, "brightness-levels");
+	if (num_levels > 1) {
+		int i;
+		unsigned int db;
+		u32 *levels = NULL;
+
+		levels = devm_kzalloc(dev, sizeof(u32) * num_levels,
+				      GFP_KERNEL);
+		if (!levels)
+			return -ENOMEM;
+
+		ret = of_property_read_u32_array(node, "brightness-levels",
+						levels,
+						num_levels);
+		if (ret < 0)
+			return ret;
+
+		/*
+		 * Try to map actual LED brightness to backlight brightness
+		 * level
+		 */
+		db = priv->default_brightness;
+		for (i = 0 ; i < num_levels; i++) {
+			if ((i && db > levels[i-1]) && db <= levels[i])
+				break;
+		}
+		priv->default_brightness = i;
+		priv->max_brightness = num_levels - 1;
+		priv->levels = levels;
+	} else if (num_levels >= 0)
+		dev_warn(dev, "Not enough levels defined\n");
+
+	ret = of_property_read_u32(node, "default-brightness-level", &value);
+	if (!ret && value <= priv->max_brightness)
+		priv->default_brightness = value;
+	else if (!ret  && value > priv->max_brightness)
+		dev_warn(dev, "Invalid default brightness. Ignoring it\n");
+
+	return 0;
+}
+
+static int led_bl_probe(struct platform_device *pdev)
+{
+	struct backlight_properties props;
+	struct led_bl_data *priv;
+	int ret, i;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, priv);
+
+	priv->dev = &pdev->dev;
+
+	ret = led_bl_get_leds(&pdev->dev, priv);
+	if (ret)
+		return ret;
+
+	ret = led_bl_parse_levels(&pdev->dev, priv);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Failed to parse DT data\n");
+		return ret;
+	}
+
+	memset(&props, 0, sizeof(struct backlight_properties));
+	props.type = BACKLIGHT_RAW;
+	props.max_brightness = priv->max_brightness;
+	props.brightness = priv->default_brightness;
+	props.power = (priv->default_brightness > 0) ? FB_BLANK_POWERDOWN :
+		      FB_BLANK_UNBLANK;
+	priv->bl_dev = backlight_device_register(dev_name(&pdev->dev),
+			&pdev->dev, priv, &led_bl_ops, &props);
+	if (IS_ERR(priv->bl_dev)) {
+		dev_err(&pdev->dev, "Failed to register backlight\n");
+		return PTR_ERR(priv->bl_dev);
+	}
+
+	for (i = 0; i < priv->nb_leds; i++)
+		led_sysfs_disable(priv->leds[i]);
+
+	backlight_update_status(priv->bl_dev);
+
+	return 0;
+}
+
+static int led_bl_remove(struct platform_device *pdev)
+{
+	struct led_bl_data *priv = platform_get_drvdata(pdev);
+	struct backlight_device *bl = priv->bl_dev;
+	int i;
+
+	backlight_device_unregister(bl);
+
+	led_bl_power_off(priv);
+	for (i = 0; i < priv->nb_leds; i++)
+		led_sysfs_enable(priv->leds[i]);
+
+	return 0;
+}
+
+static const struct of_device_id led_bl_of_match[] = {
+	{ .compatible = "led-backlight" },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(of, led_bl_of_match);
+
+static struct platform_driver led_bl_driver = {
+	.driver		= {
+		.name		= "led-backlight",
+		.of_match_table	= of_match_ptr(led_bl_of_match),
+	},
+	.probe		= led_bl_probe,
+	.remove		= led_bl_remove,
+};
+
+module_platform_driver(led_bl_driver);
+
+MODULE_DESCRIPTION("LED based Backlight Driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:led-backlight");