Added S60-X to keyboards with two layouts.

.gitignore

@@ -28,3 +28,4 @@ CMakeLists.txt
 .settings/
 .idea
 .browse.VC.db*
+*.stackdump

keyboards/s60-x/Makefile

@@ -0,0 +1,75 @@
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes        # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+
+ifndef QUANTUM_DIR
+	include ../../Makefile
+endif
+
+

keyboards/s60-x/config.h

@@ -0,0 +1,164 @@
+/*
+Copyright 2012 Jun Wako <[email protected]>
+Copyright 2016 Julien Pecqueur <[email protected]>
+Copyright 2016 Felix Uhl <[email protected]>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Massdrop
+#define PRODUCT         S60-X
+#define DESCRIPTION     q.m.k. keyboard firmware for S60-X
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { B7, B3, B2, B1, B0 }
+#define MATRIX_COL_PINS { D0, D1, D2, D3, D5, D4, D6, D7, B4, B5, B6, C6, C7, E6, F1 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+#define NO_ACTION_ONESHOT
+#define NO_ACTION_MACRO
+#define NO_ACTION_FUNCTION
+
+#endif

keyboards/s60-x/keymaps/default/Makefile

@@ -0,0 +1,21 @@
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif

keyboards/s60-x/keymaps/default/keymap.c

@@ -0,0 +1,92 @@
+/*
+Copyright 2016 Julien Pecqueur <[email protected]>
+Copyright 2016 Felix Uhl <[email protected]>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include "s60-x.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+	/* Layout 0: Default Layer
+	* ,-----------------------------------------------------------.
+	* |`  |  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|Backsp |
+	* |-----------------------------------------------------------|
+	* |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|    \|
+	* |-----------------------------------------------------------|
+	* |Ctrl  |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|Return  |
+	* |-----------------------------------------------------------|
+	* |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  .|  /|Shift     |
+	* |-----------------------------------------------------------|
+	* |Fn1 |Gui |Alt |        SpaceFn         |Alt |Gui |App |Ctrl|
+	* `-----------------------------------------------------------'
+	*/
+	KEYMAP(
+		GRV,  1,    2,    3,    4,    5,    6,    7,    8,    9,    0,    MINS, EQL,  NO,   BSPC, \
+		TAB,  Q,    W,    E,    R,    T,    Y,    U,    I,    O,    P,    LBRC, RBRC, BSLS, \
+		LCTL, A,    S,    D,    F,    G,    H,    J,    K,    L,    SCLN, QUOT, NO,   ENT,  \
+		LSFT, NO,   Z,    X,    C,    V,    B,    N,    M,    COMM, DOT,  SLSH, NO,   RSFT, NO, \
+		FN1,  LGUI, LALT,             FN0,                          RALT, RGUI, APP,  RCTL),
+
+	/* Layout 1: Function Layer
+	* ,-----------------------------------------------------------.
+	* |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delete |
+	* |-----------------------------------------------------------|
+	* |     |Prv|Ply|Nxt|Stp|   |   |PUp|Up |PDn|   |Slk|Pau|Ins  |
+	* |-----------------------------------------------------------|
+	* |      |Vl-|Mut|Vl+|   |   |Hom|Lef|Dow|Rig|End|   |PEnt    |
+	* |-----------------------------------------------------------|
+	* |        |Prt|Cut|Cop|Pst|Cal|   |   |   |   |   |CapsLock  |
+	* |-----------------------------------------------------------|
+	* |    |    |    |                        |    |    |    |    |
+	* `-----------------------------------------------------------'
+	*/
+	KEYMAP(
+		ESC,  F1,   F2,   F3,   F4,   F5,   F6,   F7,   F8,   F9,   F10,  F11,  F12,  TRNS, DEL,  \
+		TRNS, MPRV, MPLY, MNXT, MSTP, TRNS, TRNS, PGUP, UP,   PGDN, TRNS, SLCK, PAUS, INS,  \
+		TRNS, VOLD, MUTE, VOLU, TRNS, TRNS, HOME, LEFT, DOWN, RGHT, END,  TRNS, TRNS, PENT, \
+		TRNS, TRNS, PSCR, FN2,  FN3,  FN4,  CALC, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, CAPS, TRNS, \
+		TRNS, TRNS, TRNS,             TRNS,                         TRNS, TRNS, TRNS, TRNS),
+};
+
+/*
+* Fn action definition
+*/
+const uint16_t PROGMEM fn_actions[] = {
+	[0] = ACTION_LAYER_TAP_KEY(1, KC_SPACE),    /* SpaceFn layout 1 */
+	[1] = ACTION_LAYER_MOMENTARY(1),            /* Momentary layout 1 */
+	[2] = ACTION_MODS_KEY(MOD_LSFT, KC_DEL),    /* Cut  */
+	[3] = ACTION_MODS_KEY(MOD_LCTL, KC_INS),    /* Copy  */
+	[4] = ACTION_MODS_KEY(MOD_LSFT, KC_INS),    /* Paste */
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+    return MACRO_NONE;
+};
+
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/s60-x/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for s60-x

keyboards/s60-x/keymaps/felix/Makefile

@@ -0,0 +1,21 @@
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = yes       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes         # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+NKRO_ENABLE = no           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif